Setting
the
Subwoofer
Level
You
can change the Subwoofer Level to create your own tonal
preference.
1 Press
SOUND
SETUP
to activate the Sound Setting
mode.
2
Turn
the
Rotary
encoder
to select the SUBW
LEVEL Adjustment mode, and then press
o../ENT.
SUBW
LEVEL*'
H BASS*2 H TREBLE*2 H HPF*2
H
SUBWLEVEL
3
Turn
the
Rotary
encoder
to select the desired
subwoofer level (0-+15).
•
/f
no operation is petformed
for
/5
seconds, the unit will return to
normal mode automatically.
• When subwoofer is set to OFF and DEFEAT
is
set to ON, pressing
the SOUND SETUP button momentarily will not befunctional.
*'
When the subwoofer mode is set
to
OFF, its level cannot be adjusted,
refer
to
"Turning Subwoofer ON/OFF" (page /4).
The adjustment can also be made by pressing
Rotary encoder
(AUDIO). Refer
to
"Adjusting Subwoofer Level/Bass Levei/Treble
LevellBalance (Between Left and Right)/Fader (Between Front and
Rear)/Defeat" (page /2).
*2 The function is inoperable when DEFEAT is set to ON.
Setting
the
Bass
Control
You
can change the Bass Frequency emphasis to create your own tonal
preference.
1 Press
SOUND
SETUP
to activate the Sound Setting
mode.
2
Turn
the
Rotary
encoder
to select the BASS
Adjustment mode, and then press
o../ENT.
SUBW LEVEL*3 H BASs*4 H TREBLE*4 H HPF*4
H SUBW LEVEL
3-1 Press
BAND
to select the desired bass center
frequency.
80
Hz,,)
100
Hz
....
)
200
Hz")
60
Hz'-)
80
Hz
Emphasizes the displayed bass frequency ranges.
3-2
Press
SOURCE/<!.>
to select the desired bass
bandwidth.
[JNarr~W)
:.::
~
:
~
~~
(~de)
=:J
Changes the boosted bass bandwidth to wide or narrow. A
wider setting will boost a wide range of frequencies above
and below the center frequency. A narrower setting will
boost only frequencies near the center frequency.
:;seijl'!li!filfBass:
E~ve
3-3,.5Turn the
Rotary
encoder
to select the desired
bass level
(-7-+7).
You
can emphasize or weaken the bass level.
4 Press and hold
~
IESC
for at least 2 seconds to
return to normal mode.
•
Ifno
operation is
petfonnedfor
15 seconds. the unit will return to
normaL mode automatically.
• The bass level sellings will be individually memorized
for
each
source (FM, AM.
CD,
etc.) until the selling is changed. The bass
frequency and bass bandwidth sellings adjusted
for
one source are
effective
for
all other sources (FM, AM,
CD,
etc.).
• Depending on the connected devices, some functions
and
display
indications do not work. However; Bass
LeveL
is still adjustable
if
an
audio processor with the Bassfunction is connected.
• When subwoofer is set
to
OFF and DEFEAT
is
set to ON, pressing
the SOUND SETUP bullon momentarily will not be functional.
*3 When the subwoofer mode
is
set to OFF, its level cannot be adjusted.
Refer
to
"Turning Subwoofer ON/OFF" (page /4).
~
Thefunction is inoperable when DEFEAT is set
to
ON.
*5 The adjustment can also be made by pressing Rotary encoder
(AUDIO). Refer
to
"Adjusting Subwoofer Level/Bass Levei/Treble
LeveL/Balance (Between Left and Right)/Fader (Between Front and
Rear)lDefeat" (page /2).
Setting
the
Treble
Control
You
can change the Treble Frequency emphasis to create your own tonal
preference.
1 Press
SOUND
SETUP
to activate the Sound Setting
mode.
2
Turn
the
Rotary
encoder
to select the TREBLE
Adjustment mode, and then press
o../ENT.
SUBW LEVEL
*6
~-)
BASs*7 H TREBLE*7 H HPF*7
H SUBW LEVEL
3-1 Press
BAND
to select the desired treble center
frequency.
10.0
kHz
~
12.5
kHz
~
15.0
kHz
~
17.5
kHz
~
10.0
kHz
Emphasizes the displayed treble frequency ranges.
3-2,.8Turn the
Rotary
encoder
to select the desired
treble level
(-7-+7).
You
can emphasize or weaken the treble level.
4 Press and hold
~
IESC
for at least 2 seconds to
return to normal mode.
•
Ifno
operation is
petformedfor
15
seconds. the unit will return
to
normal mode automatically.
• The treble level sellings will be individually memorized
for
each
source (FM, AM,
CD,
etc.) until the selling is changed. The Treble
frequency sellings adjusted
for
one source are effective
for
all other
sources (FM, AM.
CD,
etc.).
13-EN
To Next Page
Loading...
