SUBWSYS
1:
SUBWSYS2:
• Depending
on
the
cOll1lected
devices. some functions and display
indications
do
not work. However. Treble Level is still adjustable
if
lIIl
audio processor wilh the Treble function is connected.
• When .wbwoofer is set
to
OFF and DEFEAT
is
set to
ON.
pressing
the SOUND SETUP button momentarily
wil/not
befunctional.
*6
When the subwoofer mode
is
set
to
OFF.
its level
CUll/lOt
be adjusted.
Refer
to "Turning Subwoofer ON/OFF" (page
14).
*7
The function
is
inoperable when DEFEAT is set to
ON.
*8
The adjustment can also be made by pressing Rotary encoder
(AUD/O). Refer
to "Adjusting Subwoofer Level/Bass LevellTreble
Level/Balance (Between Left and Right)/Fader (Between Front and
Rear)/Defeat" (page
12).
Adjusting
the
High
Pass
Filter
The High Pass Filter on this unit can be adjusted to suit your personal
taste.
1 Press
SOUND
SETUP
to activate the Sound Setting
mode.
2 Turn the
Rotary
encoder
to select the High Pass
Filter (HPF) Adjustment mode, and then press
0..
lENT.
SUBW LEVEL*9 H
BASS'
to H TREBLE'IO H HPF*IO
H SUBWLEVEL
3 Turn the
Rotary
encoder
to select the High Pass
Filter frequency.
OFF H 60 Hz H 80 Hz H 100 Hz
4 Press and hold
:=:::>
IESC
for at least 2 seconds to
return to normal mode.
•
Ifno
operation is performedfor
15
seconds, the unit will return to
normal mode automatically.
• When an
extenwl
audio processor is connected, this setting cannot
be made.
• When subwoofer is sel
to
OFF and DEFEAT
is
set to
ON,
pressing
the SOUND SETUP button momentarily will not befunctional.
*9
When the subwo(}fer mode
is
set 10 OFF. its level cannot be adjusted.
Refer
to
''Turning Subwoofer ON/OFF" (page 14).
*IOThefunction
is inoperable when DEFEAT
is
set
to
ON.
Turning
loudness
On/Off
Loudness introduces a special low-and high-frequency emphasis at
low
listening levels. This compensates for the ear's decreased sensitivity
to
bass and treble sound.
Press and hold
Rotary
encoder
(LOUD) for at least 2
seconds to activate or deactivate the loudness mode.
• When an external audio processor is connected, this setting cannot
be made.
• The function
is inoperable when DEFEAT is set
to
ON.
14-EN
Turning
Subwoofer
ON/OFF
When the subwoofer
is
on. you can adjust the subwoofer output level
(refer
to
page
13).
1 Press and hold
SOUND
SETUP
for at least 2
seconds to activate the Subwoofer selection mode.
2 Turn the
Rotary
encoder
to select the
SUBWOOFER mode, and then press
Q./ENT.
SUBWOOFER H SUBW SYSTEM*II H SUBWOOFER
3 Turn the
Rotary
encoder
to select SUBW ON/OFF,
and then press
Q./ENT.
SUBW ON (Initial setting) H SUBW OFF
4 Press and hold
:=:::>
/ESC for at least 2 seconds to
return to normal mode.
•
Ifno
operation is
perfonnedfor
15 seconds. the unit will return
to
normal mode automalically.
,I
tDisplayed only when SUBWOOFER
is
sel
to
ON.
Setting
the
Subwoofer
System
When the subwoofer is on, you can select either System I or System2
for the desired subwoofer effect.
1 Press and hold
SOUND
SETUP
for at least 2
seconds to activate the Subwoofer selection mode.
2 Turn the
Rotary
encoder
to select the SUBW
SYSTEM mode, and then press
Q.IENT.
SUBWOOFER H SUBW SYSTEM H SUBWOOFER
3 Turn the
Rotary
encoder
to select SUBW SYS 1 or
SUBW SYS
2,
and then press
0..
lENT.
Select
either SYS 1
or
SYS 2
for
the
desired
subwoofer
effect.
SUBW
SYS
1 (Initial setting) H SUBW
SYS
2
Subwoofer level changes according to the
main volume setting.
Subwoofer level change is different from the
main volume setting. For example. even at
low volume settings, the subwoofer is still
audible.
4 Press and hold
:=:::>
IESC
for at least 2 seconds to
return to normal mode.
•
If
no operation is performedfor
15
seconds. the unil will return to
normal mode automatically.
• Thisfunction
is
inoperable when SUBWOOFER
is
set to OFF.
To Next Page
Loading...
