4.2ch (FRONT/REAR/SUSW.) System
1 After selecting CROSSOVER from the SOUND
ADJUST mode, press
BAND
to select the band to be
adjusted.
4.2ch (FRONT'REARISUBW.)
System'
NORMAL (L=R)
setting Items:
LOW (SUB-W) / MID (REAR) / HIGH (FRONT)
4.2ch (FRONTIREARISUBW.) System 'INDIVIDUAL (LIR)
setting items:
L (SUB-W)-L / L (SUB-W)-R / M (REAR)-L /
M (REAR)-R / H (FRONT)-L / H (FRONT)-R
2 Press.... or
..
to select the desired cut-off frequency
(Crossover Point).
Adjustable frequency bands:
4.2ch (FRONTIREARISUBW.) System
Setting items:
20
Hz-200
Hz
3 Press SOURCEI<!> to adjust the slope.
Adjustable slope:
FLAT,
6 dB/oct., 12 dB/oct., 18 dB/oct.,
24 dB/oct.
4 Turn the
Rotary
encoder
to adjust the output level.
Adjustable output level: -12 to 0 dB.
5 Repeat steps 1 to 4 to make adjustment to the other
bands.
• While adjusting the CROSSOVER, you should consider the frequency
response
of
the connected speakers.
• About the 2.2ch (3WAY)14.2ch (FRONTIREARISUBW.) system
You
can switch
to
2.2ch (3WAY)/4.2ch (FRONTIREARISUBW)
system mode with the 2.2ch (3WAY)14.2ch (FRONTIREARISUBW.)
switch on the PXA-HIOO. For details, refer
to
the Owner's Manual
of
PXA-HIOO.
Storing the Sound Field Adjustment Settings
The SOUND ADJUST Settings containing PARAMETER
EQI
GRAPHIC EQ, T.CORRECTION and CROSSOVER settings can be
stored
in
the preset memory.
1 When the settings of SOUND ADJUST have been
completed, select
anyone
of the
preset
buttons
(1
through
6)
in
any item of the SOUND ADJUST
mode (e.g. CROSSOVER), press and hold the
desired preset buttons for at least 2 seconds.
2
Turn
the
Rotary
encoder
to select PROTECT
YESINO, and then press
Q,.IENT
to store the
adjusted contents.
PROTECT
YES
(Initial setting)
~
PROTECT NO
•
If
YES is selected, the adjusted coments are protected and stored into
the preset buttons. When you
wam
to
store the parameter into a
protected preset button, "REPLACE NOIYES" can be selected.
•
If
NO is selected, the preset is stored.
• While perform this operation, all adjusted contems
of
PARAMETER
EQ/GRAPHIC
EQ,
T.CORRECT/ON
and
CROSSOVER will be
stored in the preset buttons.
• The stored contents are not deleted even when resetting the unit
or
disconnecting the battery.
• The stored contents can be recalled by performing operation in
"Recalling the Stored Sound Field Adjustmem Settings" (page 31).
Recalling the Stored Sound Field Adjustment
Settings
The stored SOUND ADJUST Settings contain PARAMETER
EQI
GRAPHIC EQ, T.CORRECTION and CROSSOVER settings that are
stored
in
the preset memory.
1 After selecting any item of the SOUND ADJUST
mode (e.g. CROSSOVER), press
anyone
of the
preset
buttons
(1
through
6)
that has your
desired characteristic
in
memory to recall the stored
settings.
2 Press the
preset
buttons
again to return to the
SOUND ADJUST mode.
• While performing this operation, all adjustmem contents
of
PARAMETER EQIGRAPHIC
EQ,
T.CORRECT/ON and
CROSSOVER stored in the preset buttons will be recalled.
31-EN
To Next Page
Loading...
