POWER
IC
ON: The speakers are driven by the built-in
amplifier.
Setting the External Digital Input
D-AUX ON/ D-AUX OFF (Initial setting)
When an
ALPINE
Ai-NET compatible digital audio processor
(PXA-H7D
I)
and a DVD player (DVE-5207) not compatible with
Ai-NET
are connected, set D-AUX to
ON
to enjoy
5.
I-channel
surround sound.
You can change the D-AUX
NAME
display when D-AUX is set to ON.
Press
~
lENT
when D-AUX is set to ON, and select D-AUX NAME
by turning the
Rotary
encoder,
then press
~
lENT. After that,
tum
the
Rotary
encoder
to select the desired D-AUX NAME.
• Press
SOURCE/<!>
, and select the DIGITAL-AUX //lode,
and
adjust
the volume, etc.
• After input selection is completed, turn the
i~nition
~ff
and
back on
again. Setting
of
the optical digital input switch is completed.
•
Dependin~
on the connected audio processor, DVD player sound
may continue to be output, even
thou~h
the source is
chan~ed
to
another one.
If
this occurs, set the DVD player's power 10
OFF.
Rear
left
Rear
right
Front
right
Speakers
e
e
e
SPEAKER
LEFT REAR
SPEAKER
RIGHT REAR
SPEAKER
RIGHT FRONT
• No sound is produced by the system when the power output is set 10
OFF.
Turning Mute Mode On/Off (INT MUTE)
MUTE ON/ MUTE OFF (Initial setting)
7 characters (FM)
4 characters (AM)
56 characters
SHORT:
LONG:
Digital Seek ON/OFF Setting
DIG SEEK
ON
/ DIG SEEKOFF(Initial Setting)
HD
Radio Station Call Setting (STATION CALL)
SHORT (Initial setting) / LONG
In
the HD Radio mode, the number
of
display characters for the HD
Radio station name
can
be selected.
This
setting is used when the head unit
is
connected
to
the USB Adapter
for MP3 (KCA-620M).
You
can
set
the name to be displayed on the unit
depending on the device to which the USB Adapter for MP3
(KCA-620M) is connected.
•
Via
KCA-410C, up to 2 external devices with RCA output can be
connected.
In
this case, press
SOURCEI<!>
to select AUX mode and
then press
BAND
to select your desired device.
Setting the AUX Mode (V-Link)
AUX IN ON / AUX IN OFF (Initial setting)
You
can
input
TV
Ivideo sound by connecting an optional Ai-NETfRCA
Interface cable (KCA-121 B)
or
Versatile LinkTerminal (KCA-41
OC)
to
this component.
You
can
change the AUX name display when AUX
IN
is set to ON.
Press
~
lENT
when AUX IN
is
set
to ON, and select AUX NAME by
turning the
Rotary
encoder,
and then press
~
lENT.
After that, turn the
Rotary
encoder
to select the desired AUX name.
If
the KCA-4\
DC
is connected, it is possible to select two AUX names.
Changer Name Setting
CHANGER (Initial Setting)/ USB / PORTABLE
Front
left
e
SPEAKER
LEFT FRONT
AUX+ ON: Set to
ON
when a portable device
is
connected.
If
SOURCEI<!> is pressed and AUX+ is selected, the
sound of the portable device
is
input to the unit.
AUX+ OFF: When set to
OFF,
AUX+ source cannot be selected.
You can change the AUX+
NAME
display when AUX+
SETUP
is
set to
ON. Press
~
lENT
when AUX+
SETUP
is set to
ON,
and select
AUX+ NAME by turning the
Rotary
encoder,
then press
~
lENT.
After that, tum the
Rotary
encoder
to select the desired AUX+ NAME.
Setting the AUX+ Level (AUX
IN
GAIN)
LOW (Initial setting)/ HIGH
After setting to
ON
in "Setting the AUX+
SETUP
Mode", this selling
can be carried out.
Setting the AUX+ SETUP Mode
AUX+ ON/ AUX+ OFF (Initial
setting)
You can input the audio
of
an external device, (such as a Portable audio
player) to the Bluetooth interface connector
of
this unit. A special
Conversion cable (KCE-237B)
is
necessary to adapt the Bluetooth
interface connector as an AUX IN.
A portable music device and a Bluetooth INTERFACE (KCE-400BT)
cannot
be connected to the Bluetooth interface connector at the same
time.
If
a device having the interrupt feature
is
connected, audio will be
automatically muted whenever the interrupt signal is received from the
device.
LOW:
HIGH:
Decreases the external input audio level.
Increases the external input audio level.
ON:
OFF:
SEEK
UP/DOWN
is
used only
for
Digital Radio
Station.
SEEK
UP/DOWN
is
used
for
all Radio Stations.
i8-EN
To Next Page
Loading...
