IMPRINT Operation
(Optional)
Alpine introduces IMPRINT - the world's first technology that
thoroughly eliminates in-car acoustic problems that normally degrade
sound quality, which enables
us
to experience music the way the artist
intended, refer to "About IMPRINT" (page 34).
When the IMPRINT audio processor (PXA-HlOO) (sold separately)
is
connected to this unit, MultEQ and the following sound adjustment can
be performed.
SOURCEI<!>
Rotary
encoder
BAND
Q,./ENT
Adjusting
Subwoofer
Level/Bass
Level/
Treble
Level/Fader
(Between
Front
and
Rear)/Balance
(Between
Left
and
Right)
in
MultEQ
mode
You
can change these settings to create your own preference in MultEQ
(CURVE I or CURVE 2) mode.
1 Press
IMPRINT
to
activate
the
MultEQ
adjustment
mode.
2 Turn the
Rotary
encoder
to
select
the
desired item,
and then press
Q,.IENT.
SUBW
LEVEL-'
H BASS LEVEL H TREBLE LEVEL H
FADER-
2
H
BALANCE H SUBW LEVEL
".....
,.
....
~~r··~\I'
1\""';
~\
~\
/1""":
/
It.....................................................
...,1
c
\ I
rJ~.
/J
J
__
3
Turn the
Rotary
encoder
to
change
the setting
as
below, and then press
Q,./ENT.
Subwoofer level: 0 - +
15
Bass level: -7
-+
7
Treble level:
-7-+7
Fader: R15 - F15
Balance: L15 - R15
Changing
MultEQ
mode
MultEQ, developed
by
Audyssey Labs, automatically corrects the audio
for the listening environment. The system is optimized for selected
positions in the vehicle. To accomplish this, MultEQ must take
measurements
of
the vehicles response characteristics. For details on the
set up procedure, consult your authorized Alpine dealer.
~/ESC
I
Preset buUons IMPRINT
(1
through
6)
•
If
no operation is
perfonnedfor
60 seconds after selecting the
SUBW LEVEL, BASS LEVEL, TREBLE LEVEL, FADER
or
BALANCE mode the unit automatically returns
to
nonnal mode.
.'
When the SUBWOOFER mode is set to OFF, its level cannot be
adjusted,
and
the SUBWOOFER ON/OFF cannot be adjusted in
MultEQ (CURVE I
or
CURVE
2)
mode.
•2
If
you set the 2.2ch (3WAY)/4.2ch (FRONT/REARISUBW) switch
of
the IMPRINT audio processor (PXA-HlOO)
to
2.2ch (3WAY), you
cannot adjust the FADER mode. For details, refer to the Owner's
Manual
of
PXA-H100.
• Depending on the connected devices, some functions and display
indications do /lot work.
Press
and
hold
IMPRINT
for
at least 2
seconds
to
change MultEQ mode.
MULTEO OFF (Manual Mode)
-;
CURVE 1 (MultEO-1)
-;
CURVE 2 (MultEO-2)
-;
MULTEO OFF (Manual Mode)
• The Curve mode can be selected only when curve I
and
curve 2 are
stored.
• When using MultEQ, MEDIAXPANDER, MX
LEV
MODE,
CROSSOVER, T.CORR PARA, FACTORY'S
EQ.
SUBW
PHASE,
SUBW
CHANNEL,
TW
SETUP, EQ MODE, FILTER TYPE and
PARAMETER EQ/GRAPHIC EQ are set automatically. They are no
longer useradjustable.
• When an external audio processor is connected, the MultEQftlllction
cannot be used.
27-EN
To Next Page
Loading...
