2.2ch (3WAV)
System'
NORMAL (L=R)
Setting items:
LOW
/ M-L /
M-H
/ HIGH
Adjusting the Crossover Settings
Before performing the following procedures. refer
to
"About the
Crossover" (page 33).
2.2ch (3WAY) System
1 After selecting CROSSOVER from the SOUND
ADJUST mode, press
BANDto select the band to be
adjusted.
2.2ch (3WAV) System 'INDIVIDUAL
(UR)
Setting items:
L-L /
L-R
/ ML-L /
ML-R
/ MH-L / MH-R / H-L /
H-R
2
Press..
or
~
to select the desired cut-off frequency
(Crossover Point).
Adjustable frequency bands:
20
Hz-200
Hz
20
Hz-20
kHz
(1
kHz-20
kHz)*I/(20
Hz-20
kHz)*2
Setting items:
LOW
/M-L
M-H
HIGH
2.2ch (3WAV) System
*1
When MAKER'S is selected, refer to "Selling the Response Slope
for
the High Range Speaker
(TW
SETUP)" (page 28).
*2 When USER'S is selected. refer to "Selling the Response Slope
for
the High Range Speaker
(TW
SETUP)" (page 28).
3 Press SOURCEI<!> to adjust the slope.
Adjustable slope: FLAT*. 6 dB/oct..
12
dB/oct.,
18
dB/oct..
24
dB/oct.
1 After selecting T.CORRECnON from the SOUND
ADJUST mode, press
BAND to select a speaker to
be adjusted.
F-L
(Initial
setting)
F-R
....
R-L
....
R-R
_4
(Mid-L) (Mid-R) (High-L) (High-R)
SW-L
-4
SW-R
-4
F-L
(Mid-L)
2.2ch (3WAV) System
Adjusting the Time Correction
Before performing the following procedures, refer to "About Time
Correction" (page 32).
1 After selecting GRAPHIC EQ from the SOUND
ADJUST mode, press
BAND to select the band to be
adjusted.
B1--"'B2·
.....
B3
B4-~B5
B6-~B7-4B1
Band-1 (63 Hz) / Band-2 (150
Hz)
/ Band-3 (400 Hz) /
Band-4
(1
kHz) / Band-5 (2.5 kHz) / Band-6 (6.3 kHz) /
Band-7 (17.5 kHz)
2 Turn the
Rotary
encoder
to adjust the level.
Adjustable output level: -6
to
+6 dB
3
To
adjust another band, repeat steps 1 and 2, and
then adjust all bands.
Adjusting the Graphic Equalizer Curve
You
can modify the equalizer settings
to
create a response curve more
appealing
to
your personal taste.
To
adjust the graphic equalizer curve,
set the EQ MODE to GRAPHIC EQ. For details, refer to "Setting
EQ
mode" (page 29).
4.2ch (FRONT'REAR'SUBW.) System
F-L
(Initial
setting)
-)
F-R
--)
R-L
--)
R-R
-)
(Front-L) (Front-R) (Rear-L) (Rear-R)
SW-L-,
SW-R--)
F-L
(Front-L)
2 Turn the
Rotary
encoder
to adjust the distance
correction value. (0.0 to 336.6cm).
L =(distance to farthest speaker) - (distance to other
speakers)
Refer to "Time Correction Value List" on
page
32.
3 Repeat steps 1 and 2 to set another speaker.
By
selling
these values to
make
its sound reach the
listening position at the same time as the sound of other
speakers.
* FLAT can be
setfor
the HIGH slope only when USER'S is selected
in
"Selling the Response Slope
for
the High Range Speaker (TW
SETUP)" (page
28). Depending on the response characteristics
of
the speaker, care should be taken when setting the response slope to
FLAT, as speaker damage may result.
With
this unit, a message is
displayed when the response
slopefor
the high range speaker is set
to FLAT.
4 Turn the
Rotary
encoder
to adjust the output level.
Adjustable output level: -12
to
0 dB.
5 Repeat steps 1 to 4 to make adjustment to the other
bands.
30-EN
To Next Page
Loading...
