DVD
/Video
CD
Playing
DVDlVideo
CD
@E-V@E-D~~~
On DVDs and video CDs with playback control (PBC), menu screens
may appear automatically.
If
this happens, perform the operation
described below to start playback. .
o For many discs, the menu screen can also
be
displayed by pressing
MENU.
DVDmenu~~
Press
A.,
..
,
~
or
~
to select the desired item, then
press
ENT.
o For some discs it is possible to select items directly from the menu
screen using the
numeric
keypad
("0"
to "9").
o
If
the DVD-Audio disc is set to "VIDEO ON", operation can be
performed. (Refer to "Setting the DVD Audio Playback
Mode"
on
page 20.)
Video CD menu
~
Use the
numeric
keypad
("0" to "9") to select the
desired number, then press
ENT.
Displaying
a
Program
Usl
~
2 Press
A.
or
..
to select the desired program, then
press
ENTo
The selected program is played back.
o
If
PLAYUST
is selected, the playlist list screen is displayed.
o
If
a disc name
or
program name exceeds the display range, the last
character that appears in the display range is displayed as
"-"(tilda
accent).
1 Press
TOP
MENU while playing a DVD-VR disc.
The
program
list screen
is
displayed.
o Depending on the number
of
digits input, playback may
stan
automatically even
if
ENT.
is not pressed.
o The menu screen does not appear when the
PSC
function is turned
off. In this case, set VCD PLAY MODE to
tum
on the
PSC
function.
For details, refer to "Setting the Video CD Play Mode" (page 22).
Insert a disc with the label side facing up.
To
load discs, see "Handling the Magazine" on
page
7.
Playback starts.
o The reverse side
of
a double-sided DVD will not
be
played
automatically. Remove the disc,
tum
it over, and reinsen
it.
o It
may
take some time before playback starts after loading a disc.
To
return to the previous screen during Video CD playback, press
RETURN.
However, the function may vary depending on the disc.
While "INDEX
READ"
is displayed by
DivX~,
the fast-forwarding/
fast-reversing and repeatfunctions, etc., cannot be used.
o While playing back a video CD with Playback Control (PSC),
if
the SELECT screen is displayed, you can play back by pressing
and holding
~lIlfor
at
least 2 seconds.
DVD-R/DVD-RW
discs
recorded in DVD-VR
mode
can
be used.
Video-CD
discs
can
be
used.
CD-R/CD-RW/DVD-R/DVD-RW/DVD+R/DVD+RW
discs that are recorded
in
the
DivX®
mode can be
used.
DISPLAY
MENU
FOLDER DN
TOP MENU
ENT.
FOLDER UP
LIST
....
...
~
RETURN
.....
T
~III
...
•
Numeric
keypad
REPEAT
(0
to
9)
CLR
ANGLE
AUDIO
SUBTITLE
Caution
o Not allfunctions will operate
for
every DVD. See the
individual DVD's instructions
for
details on the features
supponed.
o Fingerprints on a disc
may
adversely affect playback.
If
a
problem occurs, remove the disc and check
for
fingerprints
on the playback side. Clean the disc ifnecessary.
o When using the remote control, be careful to press one
button at a time. Pressing multiple buttons
at
the same time
may cause erroneous operation.
o
If
you switch the
power
or
ignition key
OFF,
or
change
sources during playback, playback will continue where you
left
off
when you resume playback.
o
If
you try to perform an invalid operation (based on the type
of
disc being played), the following mark is displayed on the
monitor screen:
~
.'
(When the red
~
indicator is displayed, disc operation is
prohibited.
When the white
~
indicator is displayed, unit playback is
prohibited.)
Disc types that can be used for each heading are
represented by the following marks.
@D-iZ)
DVD
Commercial Video discs (used for the
distribution of movies, etc.) or a DVD-R/DVD-RW,
DVD+R/DVD+RW recorded
in
a video mode can be
used.
(including discs containing both
DVD
video and DVD
audio data that are played back when "DVD-V·
is
set
in
"Setting the
DVD
Audio Playback Mode"
(page 20)).
DVD Commercial
Audio
discs
can
be
used.
@E-y
~
~
~
lO.EN
To Next Page
Loading...
