o For some discs, the picture may not be set to the selected screen
size. (For details, refer to the explanation on the disc's jacket.)
o Pressing
RETURN
will return to the previous screen.
The setting is made to output audio from the connected Ai-NET
compatible head unit.
Setting item: MODEL SETUP
Setting contents: DVD CHG (Initial setting) / CD CHG
OVO
GHG: Set when a head unit sold after January 2008 is
connected.
* Even
if
the head unit is sold after January 2008, "CD
CHG"
may
or
may not be set. Refer to the Owner's Manual
of
the connected
head unit as to whether "CD
CHG"
or
"DVD CHG" should be
set.
GO
GHG: Set when a head unit sold earlier than December
2007 is connected.
After the setting is complete, tum the ignition key off and on again.
o
If
this setting is switched, you should reset. Refer to "Initial System
Start-Up" (page
9).
o
To
recall the IVA-Dl06, etc. image, switch the VISUAL button on
the IVA-Dl06.
Depending on the connected
Ai-NET
compatible head unit, even
though an
Ai-NET
is set
to
CD CHG, availablefunctions
or
displays
rrwy
vary.
Setting the Connected Head
Unit
MANUAL: If a playback disc signal differs from the
signal system on the connected monitor,
"VIDEO SIGNAL
SYSTEM
IS
NOT
CORRECT" is displayed.
AUTO CHANGE: Image is output by converting the played
back disc to the signal system of the monitor.
AUTO SELECT: Outputs an image acc<ording to the disc
signal to be played back.
(only when both an NTSC/PAL compatible
monitor is connected.)
* After you have changed the setting from AUTO CHANGE to
MANUAL
or
to AUTO SELECT,
or
from MANUAL
or
AUTO
SELECT to AUTO CHANGE, turn
off
the DHA-S690 power. Then
when you turn on the power next time, the setting is carried out.
When the DHA-S690 power is turned
off
and on again, perform the
following operation.
o
If
Ai-NET
is not connected: turn
off
PWR on the remote control
and then turn it on again.
o
If
Ai-NET
is connected: turn
off
the connected head unit power
and then turn it on again,
or
change the source.
o
If
you set to AUTO CHANGE, the image
rrwy
show some
deterioration compared to the original.
Setting
the
Disc Change
When the DVD disc main story playback is finished, the disc will
automatically change to the next main story disc.
Setting item: AUTO DISC CHANGE
Setting contents: OFF(Initial setting)/ ON
o The function may not be available depending on the disc.
Delaying Image
Output
Use this function when an external audio processor
is
connected.
Depending on the connected audio processor, the audio and image
currently played back may not be output at the same time. In this
case, you can output an image delayed by
0.1
second by setting to
ON.
Setting item: VIDEO DELAY
Setting contents: OFF(Initial setting) / ON
ON: Output image
is
delayed
by
0.1
second.
o
If
a disc with a high compression rate is played back, the image
and
audio may be distorted.
Setting theTV System
You
can select the output playback method
of
an NTSC or PAL signal
disc.
Setting items: TV SCREEN
~
TV SYSTEM
Setting
content:
MANUAL / AUTO CHANGE (Initial setting) /
AUTO SELECT
c:::::>
/
16:9
(WIDE)
Select this when
connected to a wide
screen
TV.
4:3
LB
(LETTER BOX)
Select this when connected to a
conventional 4:3 size (normal
TV
aspect ratio) monitor. There may
be black bands visible at the top
and bottom of the screen (when
playing a 16:9 size movie). The
width of these stripes will depend
upon the original aspect ratio of the theatre release of the
movie.
o When settings are changed, old settings are overwritten. Make a
note
of
the current settings before making changes. The settings are
not cleared even when the vehicle's battery is disconnected.
Switching
the
Background
Color
You
can select the background colors from 2 types preset or color 4
types.
Setting item: BACK PICTURE
Settingcontents:
TYPE-1
(Initial setting)/ TYPE-2 / COLOR *
* COLOR
~
BLACK
I GRAY I BLUE I GREEN
Setting
the
TV Screen
Use the procedure described below to set the output screen according
to the type
of
TV monitor being used.
Setting Items:TV SCREEN
~
ASPECT
Setting contents:
16:9(WIDE) (Initial setting)
/4:3
(LETTER
BOX) /
4:3
(PAN SCAN)
4:3 PAN (PAN SCAN)
Select this when
connected to a
conventional 4:3 size
monitor. The picture will fill
the entire
TV
screen.
However, due to the
mismatch in aspect ratio,
parts of the movie at the extreme left and right sides will not
be visible (when playing a 16:9 size movie).
Playing back a Main
Story
directly
This function skips warnings, precautions, etc., initially displayed
when you play back a DVD, and goes straight to the main Story.
Setting item: MAIN STORY
Setting content: OFF (Initial setting)/ ON
If
you
want
to
play
back
the
main
Story directly, set to ON.
o The function
rrwy
not be available depending on the disc.
Selecting
the
Button
on
the
Image Screen automatically
You
can automatically select the buttons displayed on the top menu!
menu image screen by setting time (seconds) without setting
manually.
Setting item: AUTO DVD MENU
Setting content: OFF(Initial setting)/ SETTIME
(1-15
sec)
SET TIME: Set your desired duration
(1
to 15 seconds) using
the numeric keypad. After the set time has
passed, the buttons are automatically selected.
(For example, if 8 seconds
is
set, press
8,
and
then press ENT.)
21.EN
To Next Page
Loading...
