Arcom RC-210 - Page 49

To Next Page

To Previous Page

When the upload is complete, Updater will inform

you and the the RC210 should start, running the

update you just installed.

Click OK, then Exit to close Updater. You are all

done!

Main Page

Table of Contents3
Command Reference6
Command Structure6
Default Commands Accessible When Unlocked7
- Receiver Enable/Disable7
- Transmitter Enable/Disable7
- Carrier/Ctcss Access7
- Touchtone© Covertone7
- Courtesy Tone Selection7
- Kerchunk Filtering7
- Half/Full Duplex Operation8
- Port 3 for Control Receiver8
- Monitoring a Port from Other Ports8
- Linking Ports Quickly9
- MIX Monitored Audio with this Port RX Audio9
Mute DTMF ON/OFF9
- Speech Override ON/OFF9
- Speech ID Override ON/OFF9
- Enable/Disable Port DTMF9
- Require/Not Require CTCSS for DTMF10
- Auxiliary Audio Inputs10
- General Logic Outputs10
- Extended Logic Outputs10
- Aborting ID's on DTMF11
- Remote Base Operation11
- Using the Doug Hall RBI-1 Remote Base Interface12
- Remote Base Power Select12
- Memory Select12
- Command Macros13
- Message Macros13
- ID Extras13
- Custom Command Prefix13
- Meter Alarms14
- Real Time Clock and Calendar14
Programming the Rc-21015
General Programming Overview15
- Unlock Code Programming15
- Locking (Leaving Program Mode)16
- Programming a Custom Lock Code16
- Programming a Custom Terminator Digit16
- A Word of Caution Regarding the Terminator Digit16
Port Unique Versus Global Programming17
- Port Unique Programming17
- Timer Programming17
- Hang Time17
- Time out Timer17
- Initial ID Timer17
- Pending ID Timer17
- Fan Timer18
- Port Inactivity Timer18
- DTMF Mute Timer18
- CTCSS Encode Dropout Timer18
- Alarm Timers18
- Auxiliary Audio Timers19
- Alarm Debounce Timer19
- Kerchunk Filter Timer19
- Pending ID Speech Timer19
- Periodic Message Timer19
- CTCSS Encode Control Line Polarity19
- Setting the Real Time Clock and Calendar20
- Year Readback20
- Adding a Correction Factor to the Real Time Clock20
- Remote Base Programming21
- Remote Base Prefix21
Programming the RC-210 Command Macros22
- Command Macros22
- Using Command Macros to Remap Controller Functions23
- Command Macro Priority23
- Message Macros24
- Tail Messages24
- Some Practical Examples of Tail Message Programming25
- Speech Control Within Command Macros26
- List of Port Direction Commands for Use in Macros27
- Controlling Command Macro Access by Port27
- Erasing All Command Macros27
- Erasing Command Macros27
- Startup Macro27
Special Features28
- Temporarily Disabling ID's and Timeout Timer28
DTMF Memories28
- DTMF Digits Duration and Time between Digits28
- Macro Function Number List29
- Macro Function Number List (Continued)30
- Macro Function Number List (Continued)31
The Scheduler32
- How Do We Define Setpoints32
- Recurring Voice Messages32
- Plan! Plan! Plan33
- Erasing Setpoints34
- Voice Message Editing and Ids34
ID Extras34
- Enable/Disable Voice Ids34
- Using the Digital Voice Recorder (DVR)35
- Recording DVR Tracks35
- Playing a Recorded DVR Track35
- Erasing Tracks35
- Editing Recorded Tracks35
- Finding out How Much Recording Time You Have Left36
- Auxiliary Audio Inputs36
- Resetting the RC-21036
- CW Speed Programming37
- CW Tone Programming37
- CW Message Programming37
- Courtesy Tone Programming38
- Courtesy Tone Behavior When Ports Are Linked39
- Programming Meter Faces - 10-Bit A/D Converters40
- Programming Meter Alarms41
- A Practical Example41
- The Differences between Accuracy and Precision42
- Programming the Reference Voltage Value for the A/D Converters42
- Measuring Voltages Higher than Vref - a Practical Example43
- Alarm Programming44
- Using Auxiliary Audio Inputs with an Alarm44
- Using Auxiliary Audio Inputs with a Macro44
- Alarm Timers44
- Resetting the Unlock Codes44
Updating the Firmware45
- Downloading and Installing the Required Software on Your Computer45
Programming Cable45
Downloading Firmware Updates45
- Frequency Agile Radios Supported (Firmware Version 4.1)50
- Factory Default Programming Values50
Appendix A50
- CTCSS Codes51
Appendix B51
- Default Factory Command Codes52
Appendix C52
- Programming Commands Quick Reference53
Vocabulary List54
Audio Spectrum Analyzer Software57
The RC-210 Development and Testing Team57
Arcom Communications No-Nonsense License Agreement for the Operating Firmware of the Rc-210 Repeater Controller58

Arcom RC-210 - Page 49

Table of Contents

Related product manuals