Argo I Series User Manual

EN
77
AIR IONIZER
Pressing the button (symbol on the display) the air
ionizer is activated; this is very effective to prevent bad
odours and to eliminate bacteria and micro-organisms.
NOTE
The filter is active only if the internal fan is operating.
What does the NIGHT mode mean?
When you select the NIGHT mode, the air conditioner will
modify automatically the set temperature after 60 minutes.
This enables you to save energy without sacrificing your
comfort.
OPERATING MODE SET TEMPERATURE CHANGE
Heating Lowered by 2 °C
Cooling and Dry Raised by 1 °C
During the night mode the internal fan speed is
automatically lowered and reduces the noise.
NOTA
The air conditioner will automatically operate by switching
from heating to cooling operation (or vice versa) in order
to maintain the set temperature.
A
ONON ON
Δ 1 H Δ 1 H
MIN. MAX.
A
B
C
C
B
A
27
26
25
24
23
22
21
20
19
Example of operation diagram in the (Auto) mode
with the set room temperature at 23°C.
NOTE
The air conditioner changes the operation mode (from cool
to heat or vice versa, if one of the following conditions
occurs:
- ZONE A: changes if the difference between the room
temperature and the temperature set on the remote
control unit is at least 3°C..
- ZONE B: changes if the difference between the room
temperature and the temperature set on the remote
control unit is at least 1°C, one hour after the compressor
stop.
- ZONE C: never changes if the difference between the
room temperature and the temperature set on the remote
control unit is no more than 1°C.
4. Press the button to select the fan speed.
DEHUMIDIFYING MODE (DRY)
1. Turn on the unit with the ON / OFF button
2. Press the button until the DEHUMIDIFYING symbol
appears on the display .
3. Press the buttons to set the desired temperature
( the temperature range is between 10 °C and 32 °C ).
• Use DRY operation when you want to reduce the
humidity in the room.
•
Once the room temperature reaches the set level, the
unit repeats the cycle of turning on / off automatically.
• During DRY operation, the fan speed is automatically
set (Remote control lamp is ON) to maximize
dehumidification.
• When the room temperature drops below the set
temperature, the unit still continues to operate at a low
temperature and could therefore further reduce the room
temperature in small rooms.
• Dry operation is not possible if the indoor temperature
is less than 10 °C.
NOTES
35*+
9+:
SET
THE DISPLAY SHOWS THE
SELECTED TEMPERATURE
AND THE WORD “SET”.
AFTER 5 SECONDS FROM THE
REQUIRED TEMPERATURE
SETTING THE DISPLAY
WILL SHOW THE ROOM
TEMPERATURE AGAIN.
AUTO
If you want to make air circulate without any temperature
control, press the button until the FAN symbol
appears on the display .
FAN ONLY MODE
35*+
9+:
ADJUSTING THE FAN SPEED
In FAN ONLY mode, the AUTOMATIC speed corresponds
to the high speed H.
AUTOMATIC
Set with the button the “AUTO” position
. The unit automatically controls the fan speed.
When the air conditioner starts operating, the fan speed
varies according to the thermal load of the room .
NOTE
MANUALE
If you want to manually adjust the fan speed just set the
button as desired:
AUTO
AUTO
LML M
MHHVH
MH Medium-high
H High
VH Very high
L Low
ML Medium-low
M Medium
,ORZKX
This program is used to increase silence and comfort during
the night.
To activate the Night mode:
1. Press the button to set the air conditioner in cooling,
dehumidifying or heating.
2. Press the button .
3. The symbol appears on the display . Press the
button again to release the function.
NIGHT MODE
35*+
9+:
4OMNZ

Argo I Series Specifications

General

Brand	Argo
Model	I Series
Category	Air Conditioner
Language	English