8
EN
This program is used to limit the maximum electrical power
absorbed by the unit.
When the energy saving program is selected, the air conditioner
limits the absorbed power to 75% of the maximum power. This
limit can be set by modifying parameter P12 on the remote
control (see paragraph “Parameters setting”).
To activate the Energy save mode:
1. Press the button to set the air conditioner in cooling
or dehumidification.
2. Press the button .
3. The symbol
appears on the display
. Press the button
again to release the function.
ENERGY SAVING MODE (ECO)
35*+
9+:
+IU
NOTE
This function is active only if the outdoor unit has an
updated software version.
This program is used to increase the maximum power that
can be supplied by the air conditioner, even if it involves less
silence.
To activate the Turbo mode:
1. Press the button to set the air conditioner in cooling .
2. Press the button .
3. The symbol
appears on the display
. Press the button
again to release the function.
TURBO MODE
35*+
9+:
:[XHU
TIMER SELECTION
To select the timer, press the button to switch on the
remote control, then press the button to chose the
desired schedule:
:OSKX
In the event of a power failure and restoration, the timer
selection must be performed again.
NOTE
1
2
3
or “OFF”
delayed timer
timer schedule
Press the RESET button on the back of the remote control if
you want to reset all settings and return to the factory setting.
RESET BUTTON
RESET
A) DELAYED TIMER
This timer is used to start the unit (if it
is off) or to stop the unit (if it is on) after
a certain time, to set the delayed time.
1.
Press the Timer button for a few
seconds.
2. Press the arrow “up” to select the
delayed timer .
3. Press the button : the hour
indication starts flashing; set the hour
with the arrows.
4. Press the button again: the minutes
indication starts flashing; set the minutes
with the arrows.
5. Confirm with the button , then press
the button to exit the delayed timer
menu.
B) SCHEDULE
This timer is used to turn the unit on and
off at predefined times and days.
1.
Press the Timer button for a few
seconds
.
2. Press the arrow “up” to select the
schedule to be set ( , or ) .
3. Press the button : ON indication
starts flashing.
4. Press the button again: AM indication
starts flashing (you can choose AM or
PM with the arrows).
5. Press the button : the hour indication
starts flashing; set the desired hour with
the arrows.
6. Press the button again: the minutes
indication starts flashing; set the minutes
with the arrows.
7. Press the button : OFF indication
starts flashing.
8. Repeat the same procedure to set AM
or PM, hour and minutes.
9. At this point, press the “up” arrow
and WEEK will start flashing.
9. Press the button : the indication of
the first day of the week starts flashing;
set ON or OFF with the arrows, then
confirm with the button .
9. The indication of the second day of
the week starts flashing: repeat the
procedure with every day of the week,
if desired.
10. At the end press to exit the menu.
HOW TO SET SCHEDULES
S
1
M
W
T
T
F
S
WEEK
• It is possible to set up to 3 weekly schedules at different
times using the timers.
NOTE
:OSKX
35*+
9+:
35*+
9+:
35*+
9+:
:[XHU
+IU
4OMNZ
,ORZKX
:OSKX
2OMNZ
ARROWS
35*+
9+:
1
2
3
:OSKX
35*+
9+:
35*+
9+:
35*+
9+:
35*+
9+:
35*+
9+:
35*+
9+:
35*+
9+:
S
1
M
W
T
T
F
S
WEEK
35*+
9+:
:[XHU
+IU
4OMNZ
,ORZKX
:OSKX
2OMNZ
ARROWS
1
2
3
To Next Page
