Asko SIVK9DTA - User Manual

Questions and Answers

N
nancysmithSep 23, 2025
What does error code FA mean on an Asko SIVK9DTA?
- P
  pottsbryanSep 23, 2025
  If your Asko hob shows error code FA, it indicates that the mains voltage is too low. You should contact your energy supplier to address this issue.
J
Jacob MillerAug 23, 2025
Why is my Asko SIVK9DTA Hob not working and the display is blank?
- S
  Shelley CohenAug 23, 2025
  If your Asko Hob isn't working and the display is blank, this indicates there is no power supply. Check the fuses or the electric switch (if there is no plug) to ensure proper power supply.
C
Cody MorenoAug 25, 2025
What does error code F8 and F08 mean on my Asko Hob?
- S
  Stephanie SchaeferAug 25, 2025
  Error codes F8 and F08 on your Asko Hob indicate that the appliance has overheated. The appliance has been switched off because of over heating. Allow the hob to cool down before using it again, and then start again on a lower setting.
L
Lisa BishopAug 26, 2025
What does error code FAN mean on my Asko Hob?
- M
  Mary MilesAug 26, 2025
  Error code FAN on your Asko Hob means that the air circulation is not good. Make sure the venting holes under the cooking plate are open.
T
Tina BowersAug 27, 2025
What does error code F7 mean on my Asko Hob?
- C
  Casey BellAug 27, 2025
  Error code F7 on your Asko Hob indicates that the ambient temperature is not good. To resolve this, switch off all heat sources near the cooking plate.
E
Elizabeth RichardsonSep 18, 2025
What does error code F99 on Asko hob mean?
- T
  thomasdavisSep 18, 2025
  If your Asko hob shows error code F99, it means that you have pressed two or more buttons at the same time. To resolve this, ensure that you only operate one button at a time.
C
Chloe FernandezSep 15, 2025
What does error code F7 mean on an Asko SIVK9DTA Hob?
- M
  monicabaileySep 15, 2025
  If the Asko hob displays error code F7, it indicates that the ambient temperature is not optimal. To solve this, switch off all heat sources located near the cooking plate.
A
Amanda ColonSep 16, 2025
What to do if ‘br’ appears on my Asko SIVK9DTA Hob display and the touch controls are not working?
- D
  Donna BarnesSep 16, 2025
  If ‘br’ appears in the display of your Asko hob and the touch controls are not working, it means that the bridge function is activated. To restore normal operation, deactivate the bridge function.
M
martinezlucasSep 6, 2025
What to do if Asko SIVK9DTA shows error code F8 or F08?
- J
  Jason DixonSep 6, 2025
  Error code F8 or F08 on your Asko hob indicates that the appliance has overheated. The hob was automatically switched off to prevent damage. To resolve this, allow the appliance to cool down completely. After it has cooled, you can start cooking again, but it's recommended to use a lower power setting to prevent future overheating.
D
david47Sep 3, 2025
What to do if my Asko SIVK9DTA Hob shows error code FA?
- C
  Charles MossSep 4, 2025
  If your Asko Hob displays error code FA, it indicates that the mains voltage is too low. Contact your energy supplier to address this issue.