ISW73 07/21
Model W73 Overhead Concealed Closer
Non-Hold Open and Hold Open
Wood Frame Installation Instructions
Copyright © 2021, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
Phillips
Level
Tape
Measure
Framing
Square
Hex Wrenches
Plumb Bob
Grout
5/16" 3/8"
Hammer Drill
Spreader
Tool
Hammer
Flathead
Screwdriver
3/16"
for Wood
Pencil
1/4-20
#7
for Metal
AND
Drill
Pour la version francaise voir www.nortondoorcontrols.com.
READ AND FOLLOW ALL INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
This product can expose you to lead which is known to the state of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65warnings.ca.gov.
Slider
(90253)
Optional Hold Open
Assembly (90254)
Closer Body
73 LAP or
PH73 LAP (ADA)
Cover Plate
70202- (nish)
Wood Mounting Clip
(90267)
Wood
Mounting
Clip (90266)
Wood Mounting
Clip (90256)
Arm
70218- (nish)
Track
(90239)
Model W73, Center Pivot Hung
Tools Needed
Non Hold Open
Stop Block
(90255)
Components
(Supplied fasteners shown on page 3)
Pivot Kit
70224KIT- (nish)
Slider Centering
Hub (70219)
Retrot Track Spacer and
Screws, Optional (90260)
Not for new installation. Replacement
only. Consult factory.
INCH
MM
63
X.X
X.XX
X.XXX
ANGLES
FRACTIONS
SURFACE FINISH
UNLESS OTHERWISE
SPECIFIED TOLERANCES
.03
.01
.005
0°30'
1/64
NOTES:
MATERIAL AND MANUFACTURING PROCESS MUST COMPLY WITH
1.
ASSA ABLOY AMERICAS PRODUCT COMPLIANCE SPECIFICATION
DOCUMENT ID# D001117360.
E
B
A
A
B
C
D
8
7
6
5
4
DRAWN BY
matbai
MATERIAL
SEE BOM
V10_7/16/2020
SURFACE/FINISH
THIRD ANGLE
PROJECTION
C
HEAT TREATMENT
DRAWING COMPLIES
WITH ASME Y14.5M - 1994
NOTICE TO PERSONS RECEIVING THIS DRAWING AND/OR
TECHNICAL INFORMATION
The material disclosed herein is the confidential and
proprietary information of
ASSA ABLOY Accessories and Door Controls Group, Inc.
(the “Company”). This drawing and/or technical
information is issued in confidence for engineering
information only and may not be reproduced or used to
manufacture anything, including the items shown or
referred to hereon, without direct written permission from
the Company. This drawing and/or technical information
is the property of the Company and is loaned for mutual
assistance to be returned when its purpose has been
served or upon the request of the Company.
LEGACY ID
SHEET
1
OF
1
Rixson70_OHC_RetroFit
Rixson
CONFIGURATION
D001151786-006
4
8
6
5
DRAWING NUMBER (ALT ID)
VOLUME
2057.621 in³
SURFACE AREA
4464.737 in²
SIZE
C
DATE CREATED
03/11/2021
DESIGNED BY
duslaw
REV
1
SCALE
1:3
DOCUMENT ID
D001151786-006
MASS
0.041 lb
E
F
G
H
7
D
F
G
H
1
2
3
Monroe DC, NC
ASSA ABLOY Accessories and
Door Controls Group, Inc.
To Next Page
Need help?
General
