Why buttons do not react when pressed on Atag DW8114XT Dishwasher?
If the buttons on your Atag Dishwasher aren't responding, here are a few things to try: * Wait a moment and try again if you've just opened the door. * Check if the child lock is activated. * Ensure the door is open, as the buttons only work when the door is open. * Clean the buttons with a dry or slightly damp cloth if they are dirty.
How to get rid of bad odor in Atag DW8114XT Dishwasher?
If you're experiencing a bad odor in your Atag Dishwasher: * Clean around the seals and in the corners with a washing-up brush and low foaming cleaner. * If you've been using low-temperature programs for a long time, run a high-temperature program or a self-cleaning program once or twice a month.
What to do if my Atag DW8114XT does not start?
If your Atag Dishwasher isn't starting, it could be due to several reasons. First, ensure you press and hold the Start/Stop button until the display indicates the program has started. Check that the door is properly closed and the door lock clicks into place. Also, verify the fuse/circuit breaker, the plug connection to the wall socket, and that the water tap is turned on. If the Delayed Start option is active, press and hold Start/Stop for three seconds to cancel it. Finally, inspect for any overflow/leaks. If you hear a whirring sound that doesn't stop when the power is off, turn off the water tap, pull out the plug, and call the service department.
How to remove spots or films on dishes from my Atag DW8114XT?
If your Atag Dishwasher leaves spots or films on the dishes, consider the following: * Adjust the rinse aid dosage setting. * If using all-in-one detergent, switch brands or deactivate the TAB setting and use salt and separate rinse aid. * Refill the salt compartment if it's empty. * Adjust the water softener setting. * Ensure the salt compartment lid is tightly closed; otherwise, contact service. * For crystal, use lower temperatures and less detergent, and contact the detergent manufacturer.
Why are the dishes not clean in my Atag DW8114XT Dishwasher?
If your Atag Dishwasher isn't cleaning dishes properly, consider these potential causes: * Make sure that dishes aren't blocking the spray arms. * Clean the spray arms and middle basket spray pipes if they are blocked. * Select a program with Intensive mode for very dirty dishes. * Ensure you are using the correct detergent dosage based on water hardness. * Avoid using old detergent. * Load the dishes correctly, avoiding overcrowding. * Ensure dishes are placed to sit steadily. * Check that the filter handle is locked in the stop position. * Ensure the colored stop on the right in the bottom drain is in place.
How to remove spots left after washing in Atag DW8114XT?
If your Atag Dishwasher has spots left after washing, it could be due to lipstick and tea stains, which are difficult to remove. Try using a detergent with a bleaching agent.
How to remove grease deposits in Atag Dishwasher?
If you observe grease deposits in your Atag Dishwasher, it may be due to prolonged use of low-temperature programs. Select a program with Intensive mode to dissolve grease, or run a self-cleaning program once or twice a month.
How to get rid of bad odour in Atag DW8114XT Dishwasher?
To address a bad odour in your Atag Dishwasher, clean around the seals and in corners with a washing-up brush and low-foaming cleaner. If you consistently use low-temperature programs, run a high-temperature program or a self-cleaning program once or twice a month.
Why Atag Dishwasher buttons do not react?
If your Atag Dishwasher buttons aren't responding, wait a moment before trying again if you've just opened the door. If the child lock is activated, refer to the Settings chapter for deactivation instructions. Remember, the buttons only work when the door is open. Also, ensure the buttons are clean; wipe them with a dry or slightly damp cloth.
What to do if water remains in my Atag DW8114XT?
If you find water remains in your Atag Dishwasher after a cycle, start by cleaning the coarse and fine filters. Ensure the filters are correctly fitted and locked in position. Check for any debris in the drainage pump and clean it if necessary. Verify the drainage pump stop is in place. Inspect the drainage hose for kinks or blockages, ensuring it has a clear inner diameter of at least 14 mm where it connects to the sink unit's water trap.
General| Type | Freestanding |
|---|---|
| Place settings | 14 |
| Noise level | 44 dB |
| Water consumption | 9.5 liters |
| Number of programs | 8 |
| Delay timer | Yes |
| Half load option | Yes |
| Dimensions (HxWxD) | 850 x 600 x 600 mm |
To Next Page
