EasyManua.ls Logo

Automatic Technology GDO-8V2 EasyRoller II - User Manual

Automatic Technology GDO-8V2 EasyRoller II
24 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
GDO-8V2 EasyRoller
®
II
INSTALLATION INSTRUCTIONS | OWNERS COPY
Weather Resistant Roll Up Door Opener
PN13240

Questions and Answers

  • A
    Amy BairdAug 8, 2025
    What to do if Automatic Technology Garage Door Opener is not working with PE installed?
    • S
      Sandra JacobsAug 8, 2025
      If your Automatic Technology Garage Door Opener isn't working with the PE installed, it could be due to several reasons: * The PE beam or wiring might be faulty. Repair the PE beam or replace the wiring. * The PE beam is not aligned correctly. Re-align the optics. * The PE beam is obstructed. Remove any obstruction from the path of the PE. * The door is obstructed when closing. Remove any obstruction.
  • E
    Eddie LindseyAug 12, 2025
    How to fix Automatic Technology GDO-8V2 EasyRoller II if it will not open or close fully?
    • J
      Jacob HarrisonAug 13, 2025
      If your Automatic Technology Garage Door Opener doesn't fully open or close, it indicates that the door limits position need to be reset.
  • C
    coxjoseAug 16, 2025
    How to solve the problem when I cannot set limits on Automatic Technology Garage Door Opener?
    • O
      owolfeAug 17, 2025
      If you cannot set the limits on your Automatic Technology Garage Door Opener, the datum position might not be set correctly. In this case, reset the datum position.
  • R
    ryan24Aug 21, 2025
    Why Automatic Technology Garage Door Opener won't operate?
    • B
      brockdeborahAug 21, 2025
      Your Automatic Technology Garage Door Opener might not be operating due to several reasons: * The mains power might not be switched on, so ensure that the power is on. * There might be an obstruction in the door's path; remove any obstructions. * The door could be locked or the motor jammed; unlock the door or remove the jam. * The door tracks or hardware could be damaged, requiring service or repair by a qualified technician.
  • P
    Patricia JohnsonAug 26, 2025
    What to do if Automatic Technology GDO-8V2 EasyRoller II starts to close but automatically reverses?
    • C
      Christopher WilliamsAug 26, 2025
      If your Automatic Technology Garage Door Opener starts to close but then reverses, it could be due to: * Adverse weather conditions (wind or cold) causing the door to stiffen and become tight in the tracks. Try increasing the force margin setting or recalculating the force margin. * There might be an obstruction in the doorway. Make sure to remove any obstructions.
  • J
    Jennifer ThompsonAug 29, 2025
    Why Automatic Technology GDO-8V2 EasyRoller II Garage Door Opener operates from the button but not the transmitter?
    • J
      johnsoncynthiaAug 29, 2025
      If your Automatic Technology Garage Door Opener works with the drive unit button but not the transmitter, the cause may be: * The transmitter code is not stored in the memory. In this case, you should code the transmitter into the opener's memory. * The transmitter battery is flat. Try replacing the battery with an A23 Alkaline 12V battery.
  • B
    bennettbonnieSep 2, 2025
    What causes Automatic Technology Garage Door Opener to overshoot or not reach limits?
    • O
      Omar Smith PhDSep 2, 2025
      If your Automatic Technology Garage Door Opener is overshooting or not reaching its limits, it might be because the datum position is not set correctly. Reset the datum position.

Automatic Technology GDO-8V2 EasyRoller II Specifications

General IconGeneral
TypeRoller Door Opener
Max Door Weight100kg
Input Voltage240V AC
Motor Voltage24V DC
Maximum Door Weight100kg
Maximum Door Area16.5m²
Operating Temperature-20°C to +50°C
Radio Frequency433.92 MHz
Maximum Remote Controls64
Voltage240V AC
Warranty2 years
Safety FeaturesAuto-reverse mechanism, photoelectric sensors
Remote ControlYes
Motor TypeDC Motor
Horsepower1/2 HP
Belt TypeNot applicable

Related product manuals