Automatic Technology GDO-6v3 EasyRoller - User Manual

Automatic Technology GDO-6v3 EasyRoller

36 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

GDO-6v3 EasyRoller

®

Roll Up Garage Door Opener

INSTALLATION INSTRUCTIONS | OWNERS COPY

Featuring TrioCode

™

Technology

Part # 13236 (Manual)

Table of Contents

Questions and Answers

K
katherine37Aug 19, 2025
What to do if my Automatic Technology GDO-6v3 EasyRoller Garage Door Opener will not operate?
- P
  Patricia MyersAug 19, 2025
  If your Automatic Technology Garage Door Opener isn't working, there are several potential causes: * The mains power might not be switched on. If this is the case, switch on the mains power. * There might be an obstruction. Remove any obstructions. * The door could be locked or the motor jammed. Unlock the door or remove the jam. * The door tracks or hardware could be damaged, requiring service/repair by a qualified technician. * The opener might be in “vacation mode”. Turn off “vacation mode”.
A
Austin HaynesAug 21, 2025
Why won't my Automatic Technology GDO-6v3 EasyRoller work?
- W
  William FitzgeraldAug 21, 2025
  Your Automatic Technology Garage Door Opener might not be working due to several reasons: * The mains power might not be switched on, so switch it on. * There might be an obstruction in the door's path; remove any obstructions. * The door could be locked or the motor jammed; unlock the door or remove the jam. * The door might be in “vacation mode”; turn off “vacation mode”. * The door tracks/hardware might be damaged, requiring service/repair by a qualified technician.
M
Monica NobleAug 23, 2025
Why is the auto-close feature not working on my Automatic Technology GDO-6v3 EasyRoller?
- C
  Christopher MoranAug 25, 2025
  If the auto-close feature isn't working on your Automatic Technology Garage Door Opener, here are some possible reasons: * The PE Beam or its wiring might be faulty; repair the PE Beam or replace the wiring. * The PE Beam might not be aligned correctly; realign the optics. * The PE Beam might be obstructed; remove any obstruction from the path of the PE. * The door might be obstructed when closing; remove any obstruction. * The auto-close time might not be set. * The auto-close mode might not be set.
M
mwilliamsAug 26, 2025
How to fix an Automatic Technology Garage Door Opener that will not close all the way?
- B
  Brenda ReedAug 26, 2025
  If your Automatic Technology Garage Door Opener doesn't fully close, the door limit positions may need to be reset.
R
Rachel JacksonAug 28, 2025
How to fix an Automatic Technology GDO-6v3 EasyRoller that will not open all the way?
- J
  James BakerAug 28, 2025
  If your Automatic Technology Garage Door Opener doesn't fully open, the door limit positions may need to be reset.
S
samantha91Aug 30, 2025
What to do if the courtesy light is not working on my Automatic Technology GDO-6v3 EasyRoller Garage Door Opener?
- B
  breannadunnAug 31, 2025
  If the courtesy light on your Automatic Technology Garage Door Opener isn't working, the globe may be blown. Replace the globe.
S
Sandra FarmerSep 1, 2025
What to do if Automatic Technology GDO-6v3 EasyRoller works with the button but not the transmitter?
- L
  Lisa MarshSep 2, 2025
  If your Automatic Technology Garage Door Opener operates from the drive unit button but not from the transmitter, the issue might be: * The transmitter code is not stored in memory. You will need to code the transmitter into the opener's memory. * The transmitter has a flat battery. Replace the battery. * There's a broken battery lead inside the transmitter. Send the transmitter to installer or Automatic Technology for repair.
D
Dawn PayneSep 4, 2025
How to fix auto close on Automatic Technology GDO-6v3 EasyRoller Garage Door Opener?
- R
  Randy FranklinSep 4, 2025
  If the auto close function is not working on your Automatic Technology Garage Door Opener, consider the following: * The PE Beam or its wiring might be faulty; repair the PE Beam or replace the wiring. * The PE Beam might not be aligned correctly; re-align the optics. * There might be an obstruction in the path of the PE Beam; remove the obstruction. * The door might be obstructed when closing; remove the obstruction. * Auto close time might not be set. * Auto close mode might not be set.
N
Nathan JohnsonSep 6, 2025
Why is the light not working on my Automatic Technology Garage Door Opener?
- F
  Frank WhiteSep 6, 2025
  If the courtesy light on your Automatic Technology Garage Door Opener is not working, the globe might be down. Replace the globe.
V
veronica63Sep 8, 2025
Why does my Automatic Technology Garage Door Opener start closing but then go back up?
- K
  kellylewisSep 8, 2025
  If your Automatic Technology Garage Door Opener starts to close but then reverses, it could be due to adverse weather conditions (wind or cold) causing the door to stiffen and become tight in the tracks; in this case, increase the force margin setting. Another cause could be an obstruction in the doorway, so remove any obstructions that you find.

Summary

Important Safety Instructions

Safety Guidelines and Warnings

Crucial safety precautions for operating and installing the garage door opener.

Features

Pre-Installation Requirements

Door Operation and Suitability Checks

Essential checks and conditions before installing the opener.

Installation Location and Power Requirements

Installation - Preparation and Fitting

Preparation and Weight Bar Fitting

Steps for preparing the door and attaching the weight bar.

Installation - Door and Opener Mounting

Pinning the Door Curtain

Fitting the Opener

Procedures for attaching the opener unit to the door axle.

Installation - Opener Mounting and Final Checks

Mounting the Opener

Detailed steps for correctly mounting the opener.

Setting Travel Limits

Setting Travel Limits via Control Panel

Procedures for configuring the door's open and close positions.

Resetting Travel Limits

Setting Limits via Transmitter

Coding Transmitter for Limit Setting

Pairing a transmitter to set door travel limits.

Setting Limits Using Transmitter

Using the transmitter to define open and close positions.

Safety Obstruction Force Test

Testing the Close Cycle

Procedure to test the door's reversal upon encountering an obstruction.

Testing the Open Cycle

Procedure to test the door stopping when obstructed during opening.

Adjusting Safety Obstruction Forces

Increasing and Decreasing Force Pressure

Recalling and Recalculating Force Margins

Coding Transmitters

Transmitter Coding Methods

P.E. Beams & Auto-close Setup

Troubleshooting

Automatic Technology GDO-6v3 EasyRoller Specifications

General

Brand	Automatic Technology
Model	GDO-6v3 EasyRoller
Category	Garage Door Opener
Language	English

Related product manuals

Preview: GDO-6v4 EasyRoller

GDO-6v4 EasyRoller

Preview: GDO-6 EasyRoller

GDO-6 EasyRoller

Preview: GDO-6 v2 Slim-Drive EasyRoller

GDO-6 v2 Slim-Drive EasyRoller

GDO-4 EasyRoller

GDO-8V2 EasyRoller II

Preview: GDO-8v1 EasyRoller II

GDO-8v1 EasyRoller II

Automatic Technology GDO-6 v2

Preview: Automatic Technology GDO-11 Ero

Automatic Technology GDO-11 Ero

Preview: Automatic Technology HiRO GDO-12

Automatic Technology HiRO GDO-12

Preview: Hiro GDO-12V1

Preview: SecuraLift GDO-7V1

SecuraLift GDO-7V1

GDO-11v1 SecuraLift