Automatic Technology GDO-6v3 EasyRoller - User Manual

Automatic Technology GDO-6v3 EasyRoller

36 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

GDO-6v3 EasyRoller

®

Roll Up Garage Door Opener

INSTALLATION INSTRUCTIONS | OWNERS COPY

Featuring TrioCode

™

Technology

Part # 13236 (Manual)

Table of Contents

Questions and Answers

J
Jennifer ChurchSep 12, 2025
Why does my Automatic Technology GDO-6v3 EasyRoller work with the wall button but not the remote?
- M
  Michael ClarkSep 12, 2025
  If your Automatic Technology Garage Door Opener works with the OPERATE button but not the transmitter, consider these possibilities: * The transmitter code may not be stored in memory. * The transmitter battery might be flat, so replace it. * There might be a broken battery lead inside the transmitter; in this case, send the transmitter to installer or Automatic Technology for repair.
J
Jennifer MendozaSep 13, 2025
Why does the globe keep blowing in my Automatic Technology GDO-6v3 EasyRoller?
- T
  timothy63Sep 13, 2025
  If the globe in your Automatic Technology Garage Door Opener keeps blowing, it might be due to an incorrect globe type. Ensure you are using a festoon Type - 15W 24VD.C. globe and replace the globe.
N
Nathan KnappSep 15, 2025
Why does my Automatic Technology Garage Door Opener start closing but then reverses?
- L
  Laura VasquezSep 15, 2025
  If your Automatic Technology Garage Door Opener starts to close but then automatically reverses to the open position, it could be due to: * Adverse weather conditions (wind or cold) causing the door to stiffen and become tight in the tracks. In this case, increase the force margin setting or re-calculate the force margin. * A possible obstruction in the doorway. Make sure to remove any obstructions.

Summary

Important Safety Instructions

Safety Guidelines and Warnings

Crucial safety precautions for operating and installing the garage door opener.

Features

Pre-Installation Requirements

Door Operation and Suitability Checks

Essential checks and conditions before installing the opener.

Installation Location and Power Requirements

Installation - Preparation and Fitting

Preparation and Weight Bar Fitting

Steps for preparing the door and attaching the weight bar.

Installation - Door and Opener Mounting

Pinning the Door Curtain

Fitting the Opener

Procedures for attaching the opener unit to the door axle.

Installation - Opener Mounting and Final Checks

Mounting the Opener

Detailed steps for correctly mounting the opener.

Setting Travel Limits

Setting Travel Limits via Control Panel

Procedures for configuring the door's open and close positions.

Resetting Travel Limits

Setting Limits via Transmitter

Coding Transmitter for Limit Setting

Pairing a transmitter to set door travel limits.

Setting Limits Using Transmitter

Using the transmitter to define open and close positions.

Safety Obstruction Force Test

Testing the Close Cycle

Procedure to test the door's reversal upon encountering an obstruction.

Testing the Open Cycle

Procedure to test the door stopping when obstructed during opening.

Adjusting Safety Obstruction Forces

Increasing and Decreasing Force Pressure

Recalling and Recalculating Force Margins

Coding Transmitters

Transmitter Coding Methods

P.E. Beams & Auto-close Setup

Troubleshooting

Automatic Technology GDO-6v3 EasyRoller Specifications

General

Brand	Automatic Technology
Model	GDO-6v3 EasyRoller
Category	Garage Door Opener
Language	English

Related product manuals

Preview: GDO-6v4 EasyRoller

GDO-6v4 EasyRoller

Preview: GDO-6 EasyRoller

GDO-6 EasyRoller

Preview: GDO-6 v2 Slim-Drive EasyRoller

GDO-6 v2 Slim-Drive EasyRoller

GDO-4 EasyRoller

GDO-8V2 EasyRoller II

Preview: GDO-8v1 EasyRoller II

GDO-8v1 EasyRoller II

Automatic Technology GDO-6 v2

Preview: Automatic Technology GDO-11 Ero

Automatic Technology GDO-11 Ero

Preview: Automatic Technology HiRO GDO-12

Automatic Technology HiRO GDO-12

Preview: Hiro GDO-12V1

Preview: SecuraLift GDO-7V1

SecuraLift GDO-7V1

GDO-11v1 SecuraLift