Autronica SM4 - Boost setpoint table

To Next Page

To Previous Page

SM4 Manual by MRM-Racing V3.0

Boost setpoint table

It is good practice to have at least two rows in the table, so we can set a boost curve that is

used under normal conditions, and another boost curve that is used if the engine is overheated.

In the example Boost setpoint table in

Main Page

Default Chapter2
- Table of Contents2
Installation and Wiring Guide8
- Introduction8
- Before You Begin8
- Tools and Material that You will Need9
Installation Guide10
- Flying Lead Loom Installation on Engine10
Sensor and Device Pin Outs13
- Manifold Absolute Pressure Sensor13
- Coolant Temperature Sensor13
- Inlet Air Temperature Sensor14
- Throttle Position Sensor15
- Throttle Range Learning16
- Ignition Modules16
- Exhaust Gas Sensor (Optional)17
- Crank and Cylinder Reference Wiring17
- Flying Leads19
- Sm4 Connector Pin out20
- Output Channel Electrical Characteristics21
- Input Channel Electrical Characteristics21
Set up Guide22
- Computer Requirements22
- Installing Autronic Software22
- Starting Autronic Software22
- Basic Windows Conventions23
Software Basic Setup Guide24
- Base Settings24
- Ignition Setup25
- Injector Selection26
- I/P Cylinder & Sync26
Starting the Engine for the First Time27
- Items Required27
- Software27
- Starting the Engine27
- Direct Fire Ignition Sequence Testing28
Tuning Guide29
- Setting up the A/Ftable29
- Manual Tuning31
- Manual Tuning with the M (Maths) Key on the Keyboard31
- Tuning with Datalogs and Mixture Table32
- Autotuning33
- Throttle/Manifold Mapping34
- Setting up a Superior Launch - Control with Sm4 Chip 1.0934
- Boost Control38
Autronic Software User Guide52
- Filecal Menu52
- Edit-Window Menu53
- Menu M064
- Menu M166
- Menu M283
- Menu M389
Menu M491
- W-U Enrichment Mul91
- P-S Enrichment Mul91
- P-S Enrich Timeout91
- W-U Fast Idle Inc91
- P-S Fast Idle Inc92
- P-S Fastidle Timeout92
- W-U Accel Enrich Mul92
- W-U Decal Enleanment92
- IAC-Proportion Range92
- IAC-Closed Rpm Value92
- IAC-Minimum Opening93
- Cranking Ignition93
- Idle Ignition93
- Idle Speed Table94
- Idle Ignition Setup94
- IAC Tuning95
- IAC Limits96
- IAC TPS Follower96
- IAC Actuator Cal97
- M4 Tables Axis Setup97
Menu M597
- Boost Tune97
- Boost Setpoint 1 - 398
- Boost Dynamic Comp98
- Boost Offset99
- Boost Modifier99
- ECU Limits Setup99
- Overrun Shutdown Com100
- Overrun Shutdown Recovery100
- Rev Limiter 1100
- Rev Limiter 2100
- Cut Fuel/Ign Pattern101
- Anti-Lag Setup101
- Anti-Lag Ignition102
- Anti-Lag Cut Data103
- Anti-Lag Cool down104
- Traction Ctrl Setup104
- Traction Ctrl Tune104
- TC Power Cut Limit105
- Launch Control105
- WOT Shift105
- M5 Tables Axis Setup106
Menu M6107
- Gpc 1-4107
- Gpc 5-13107
- O/P Air con107
- O/P Fan 1107
- O/P Fan 2107
- O/P Nos108
- O/P Fuel Used108
Menu Logger108
- PC Warning & Select109
- PC Warnings Options109
- PC Min/Max/Freeze109
- PC Logger Setup110
Keystrokes Reference114
- General Keys114
- Edit Keys114
- Autotune™ Keys114
- Data Logging Keys114
Fuel System115
- Flow Estimation115
- Injector Flow Capacity115
- Fuel Pump Capacity116
- Fuel Rail & Pressure Regulator116
Ignition System117
- Dumb Ignition Modules117
- Smart Ignition Modules118
- Falling Egde & Rising Edge on Ignition Modules118
- The Coil Negative Signal118
- Direct Fire CDI Autronic 500R119
Trigger Interface121
- The Input Trigger121
- Trigger Devices122
- One Pulse Per Tdc123
- Multi Tooth Trigger124
- Motronic Trigger124
- Other Triggers124
Autronic Analyzer127
- Changing Settings127
- Most Used Functions128
Fault Finding129
- No Communication129
- N Orpm Signal129
- No Spark or Injection Pulses129
Ecu Self Diagnostic130
- Error Indicator Light130
- Diagnostic Light Fault Codes131
Ecu Specifications132
Pc and Ecu Logger Diagrams133
- Wiring Diagrams133
Pc Data Cable Diagram133
- Wiring Diagram133

Autronica SM4 - Boost setpoint table

Table of Contents