Need help?Do you have a question about the Baby Lock BLTA Altair and is the answer not in the manual?
General| Brand | Baby Lock |
|---|---|
| Model | BLTA Altair |
| Category | Sewing Machine |
| Language | English |
Settings for stitch width, vertical and horizontal fine adjustments, and presser foot controls.
Configuration of initial position, stitch page, foot controller, needle position, and thread cutting.
Adjustments for pivoting, fabric sensor system, and reinforcement priority.
Controls for speaker volume, LED light, and screen brightness.
Configurations for eco mode, shutoff support mode, and screen saver.
Options for opening screen, language, and SCS reset.
Settings related to embroidery frames, thread tension, and maximum speed.
Configurations for embroidery units, background colors, and appliqué distance.
Settings for wireless LAN connectivity, setup wizard, and status.
Options to set machine name, perform network reset, and access app guide.
Instruction on how to remove the top cover by lifting it straight up.
Instruction to remove screw covers labeled 'A' from the face plate.
Steps to remove screws 'B' and slide the face plate cover to the left.
Procedure to detach the needle plate cover.
Procedure to detach the free arm cover.
Steps to remove screws 'C' and detach the base cover.
Steps to remove cap and screw 'D' to detach the tension cover.
Steps to remove screws 'E' and lift the top machine cover from the back.
Instruction to detach the connector for the bobbin winder.
Steps to remove the screw cover and screw 'H' on the side.
Steps to remove the bottom screw and pull the side cover to the right.
Instruction to loosen screw 'I' from the left side of the cover.
Instruction to remove screw 'H' from the front free arm cover.
Procedure to swing the cover forward then down to remove.
Instructions to loosen screw 'L' and remove screw 'M'.
Instruction to loosen screw 'N' from the left side.
Information about the release tab on the front panel.
How to use a screwdriver to release a lock on the front panel.
Caution on detaching 3 hooks locked in the base plate.
Procedure to disconnect the panel board connector 'O'.
Steps to remove 5 cross-slotted screws from the embroidery unit covers.
How to lift and slice the top cover to the right.
Instruction to loosen screw 'R' on the X arm cover.
Steps to remove screw 'S' and detach the X drive cover.
Description of the new tracking system 'T'.
Description of the support roller 'U'.
Information on extended shaft links for upper and lower shafts.
Standard steps for calibrating the touch panel using test points.
Key points and notes for successful touch panel adjustment.
Procedure to start the machine to enter test mode.
Overview of the test mode selection screen and its options.
Explains test modes for serial numbers, fabric thickness, pattern adjustment, and needle drop.
Explains test modes for needle clearance, feed dog position, presser foot height, and lower thread display.
Explains test modes for upper thread display, sensor cancel, forward/reverse feed, and speed.
Explains test modes for power and switch monitoring.
Explains test modes for clear flash, thread buzzers, and NP sensor.
Explains test modes for embroidery max position and LCD check.
Explains test modes for tension adjustment, line marker position, and threading check.
Explains the test mode for switch and sensor status.
Details of sensor status for Panel PCB and Main PCB.
Explains test modes for AD, side feed, LED pointer, and dual feed check.
Explains test modes for embroidery position adjustment and touch panel check.
Explains the test mode for checking parameter defaults.
Explains the test mode for displaying the error list.
Explains the test mode for checking LEDs and the internal speaker.
Explains the test mode for checking USB host transmission status.
Explains BWD check and EEPROM USB write test modes.
Standard clearance for timing belt and belt support.
Steps to adjust the timing belt guards.
Steps to remove the 'C' clip from the bottom of the threader.
Procedure to pull down and detach the needle threader assembly.
How to assemble separated threader parts as shown.
Steps for reattaching the threader hook assembly to the plastic track.
Procedure to reconnect the spring and reinstall the 'C' clip.
Standard for parallel pattern and section length.
Standard for pattern height.
Standard for difference between upper and lower sections.
Standard for needle drop position in the center of the embroidery sheet hole.
Procedure to adjust the needle drop position using the screen.
Standard for guide line parallelism and center alignment with needle.
Procedure to adjust the guide line position, including using laser module screws.
Standard for needle drop point on the pointer beam.
Check pointer beam range from the edge of the feed dog hole.
Instruction to touch the second point of the cross-hair using the sensor pen.
Procedure to finish calibration by pressing the OK key.
Standard for X timing belt pushing force and slack.
Steps to adjust the X timing belt tension.
Standard for Y timing belt pushing force and slack.
Steps to adjust the Y timing belt tension.
To Next Page