EasyManuals Logo

B&K Reference 30 User Manual

B&K Reference 30
84 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #69 background imageLoading...
Page #69 background image
Set Zone 2 (B) product ID - Each message transmitted from your remote includes a Product Code, identifying
the manufacturer, and Zone product ID code from 1 to 16. The product ID code allows multiple B&K products to
be controlled from the same remote. Your processor actually uses two product ID codes - one for Zone 1 (A)
(normally set to ID code 1) and the other for Zone 2 (B) (normally set to ID code 2). If you have a system with
multiple B&K products then you may wish to set the Zone product ID codes to other values. Note that you cannot
set the Zone 1 (A) product ID to the same setting as Zone 2 (B) or vice versa. If you need to set Zone 1 (A) to the
current Zone 2 (B) setting then set Zone 2 (B) to some other value first.
WARNING - if you change the Zone product ID code in the processor without making the corresponding
change to the remote then the remote will no longer work. Refer to the separate remote manual for details
on changing the remote’s product ID (“device code”).
ADVANCED ZONE B SETTINGS
1 Level Control Variable
2 Fixed Level +15 dB
3 Zone ID 2
4 V2 Out
p
ut Ta
p
e
5 Link In
p
ut to Zone A No
6 Link Power to Zone A No
next item ad
j
ust
MENU advanced setu
p
3 Zone ID 2
=% =21( ,'
adjust Zone 2 (B) ID to desired valueVOLUME KNOB
(REW) or

(FF)
2
move to Zone ID
(UP) or (DOWN)
(PAUSE) or
(STOP)
1
ActionFrom Front PanelFrom Remote
Set V2 line output usage - V2 output is normally set up as a tape loop. The V2 and Zone 2 (B) output are the
current source (V1, TV, CD, DVD, etc.) except when the current selection is V2. When V2 is selected as the
source, the Zone 2 (B) output is V2 and the V2 output is the previously selected source. This prevents feedback
when the V2 inputs and outputs are connected to a tape deck or VCR. Feedback can cause high frequency
oscillations which may damage your speakers. If you don’t connect a tape deck to the V2 input and output you can
use the V2 output as an additional line out. In this mode V2 output is always the selected input including V2.
ADVANCED ZONE B SETTINGS
1 Level Control Variable
2 Fixed Level +15 dB
3 Zone ID 2
4 V2 Out
p
ut Ta
p
e
5 Link In
p
ut to Zone A No
6 Link Power to Zone A No
next item ad
j
ust
MENU advanced setu
p
4 V2 Out
p
ut Ta
p
e
=% 9 287 7$3(
ADVANCED ZONE B SETTINGS
1 Level Control Fixed
2 Fixed Level +15 dB
3 Zone ID 2
4 V2 Out
p
ut Line
5 Link In
p
ut to Zone A No
WARNING Connectin
g
a ta
p
e
recorder to V2 in LINE mode
can cause s
p
eaker dama
g
e
next item ad
j
ust
MENU advanced setu
p
4 V2 Out
p
ut Line
=% 9 287 /,1(
set for Tape or LineVOLUME KNOB
(REW) or

(FF)
2
move to V2 Output
(UP) or (DOWN)
(PAUSE) or
(STOP)
1
ActionFrom Front PanelFrom Remote
66
p/n 12857 Rev. 0717A

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the B&K Reference 30 and is the answer not in the manual?

B&K Reference 30 Specifications

General IconGeneral
BrandB&K
ModelReference 30
CategoryController
LanguageEnglish

Related product manuals