What to do if the keypad is not working properly on BANTE Measuring Instruments?
If the keypad of your BANTE Measuring Instruments isn't working correctly, the first thing you should try is replacing the batteries. This simple step can often resolve the issue.
What to do if measured value is out of range on BANTE 900P?
If your BANTE Measuring Instruments display a measured value that's out of the expected range, examine the electrode. It might be clogged, dirty, or broken. Addressing these issues can help bring the measured value back within the correct range.
What to do if zero oxygen solution is contaminated in BANTE 900P Measuring Instruments?
If the zero oxygen solution for your BANTE Measuring Instruments is contaminated, you should replace it with a fresh calibration solution to ensure accurate measurements.
What to do if DO electrolyte solution is depleted in BANTE 900P Measuring Instruments?
If the DO electrolyte solution in your BANTE Measuring Instruments is depleted, you need to refill it to ensure proper functioning of the instrument.
What to do if setting value does not match calibration solution in BANTE 900P Measuring Instruments?
If the setting value doesn't match the calibration solution in your BANTE Measuring Instruments, reset the calibration value to ensure accurate readings.
Why do I need fresh calibration solutions for BANTE Measuring Instruments?
If you're using incorrect calibration solutions with your BANTE Measuring Instruments, make sure to use fresh calibration solutions for the calibration process. This will help ensure accurate measurements.
How to rehydrate electrode of BANTE 900P?
If the electrode of your BANTE Measuring Instruments has dried out: * For a pH electrode, soak it in a 3M KCL solution for 15 minutes. * For an Ion Selective Electrode, soak it in the diluted standard solution. * For a conductivity electrode, soak it in tap water for a few minutes.
General| Brand | BANTE |
|---|---|
| Model | 900P |
| Category | Measuring Instruments |
| Language | English |
Information on environmental conditions and checking accessories after unpacking.
Describes the function of each key on the meter's keypad.
Details the purpose of each connector port on the meter.
Step-by-step guide on how to insert batteries into the meter.
Instructions for connecting pH, ORP, Ion, Conductivity, and DO probes.
Instructions for preparing pH buffer solutions for calibration.
Steps to refill the electrolyte solution for the DO probe.
Guidelines for preparing pH, ORP, Ion, Conductivity, and DO sensors before use.
Configuration options for pH measurement mode.
Configuration options for ORP measurement mode.
Configuration options for Ion measurement mode.
Configuration options for Conductivity, TDS, Salinity, and Resistivity modes.
Configuration for DO mode and general meter settings.
Setting calibration reminders and the meter's date and time.
Detailed steps to set the meter's date and time accurately.
How to enable automatic temperature compensation using a probe.
How to manually set the temperature for compensation.
Procedure for performing a single-point pH calibration.
Procedure for performing multi-point pH calibration.
How to calibrate using custom buffer solutions.
Checking electrode parameters for diagnostic purposes.
Checking the zero-point offset potential of the pH electrode.
Reviewing the slope of the pH electrode after calibration.
Steps for performing a single-point ORP calibration.
Checking the millivolt offset in the ORP measurement mode.
Available calibration points and measurement units for ion concentration.
Detailed procedure for ion concentration calibration.
Checking ion electrode diagnosis and slope values.
Choosing the correct conductivity electrode and its cell constant.
Procedure for performing a single-point conductivity calibration.
Table of acceptable conductivity calibration solutions and ranges.
Steps for performing multi-point conductivity calibration.
Guide to manually calibrating the conductivity meter.
Setting the cell constant for manual conductivity calibration.
Verifying the calibration factor of the conductivity electrode.
Procedure for 100% saturation calibration of dissolved oxygen.
Steps for performing a two-point dissolved oxygen calibration.
Calibration using zero oxygen solution for DO measurement.
Procedure for single-point DO calibration in mg/L or ppm.
Steps for two-point DO calibration in mg/L or ppm.
How to calibrate the meter's temperature reading.
Steps for performing pH measurements.
Steps for performing ORP measurements (Absolute and Relative mV).
Procedure for measuring ion concentration.
Steps for measuring Conductivity, TDS, and Resistivity.
Steps for measuring salinity (PSU and ppt).
Steps for measuring dissolved oxygen in various liquids.
Explains the auto-hold and manual hold functions.
How to store measured values into the meter's memory.
How to recall stored data from the meter's memory.
Viewing date, time, and measured values of stored data.
Introduction to the Data Acquisition System software.
Connecting meter to PC and receiving data.
How to search for specific data records in the database.
How to print measurement data sheets.
Recalling and deleting data from the acquisition system.
Viewing measurement variations using graph mode.
Setting up automatic recording of measurements at intervals.
Converting data sheets into Excel files.
Cleaning, maintenance, and reactivation of pH electrodes.
Cleaning and maintenance of ORP electrodes.
Care and maintenance guidelines for ion selective electrodes.
Cleaning and maintenance of conductivity electrodes.
Maintaining the dissolved oxygen probe, keeping the membrane moist.
Solutions for common display and operational problems.
Technical specifications for pH and mV measurements.
Technical specs for various measurement modes and temperature.
Details on hold function, stability, power off, output, and physical specs.
Table listing optional pH electrodes for different sample types.
List of optional ion selective electrodes and their measurement ranges.
Instructions for preparing electrode storage solution.
Procedures for preparing conductivity standard calibration solutions.
Formula and method to calculate the temperature coefficient.
Formula and method to calculate the TDS conversion factor.
Table relating atmospheric pressure to altitude.
Instructions for preparing zero oxygen solution for DO calibration.
Commitment to reducing hazardous substances in products.
Details on the meter's warranty period and coverage.
To Next Page
