R5910888 /00 G60 13
• For ceiling mounted installations, make sure to leave 30 mm (1.2”) between the ceiling mount and the
bottom intake vents of the projector.
To prevent battery explosion
• Danger of explosion if battery is incorrectly installed.
• Replace only with the same or equivalent type recommended by the manufacturer.
• For disposal of used batteries, always consult federal, state, local and provincial hazardous waste disposal
rules and regulations to ensure proper disposal.
On servicing
• Do not attempt to service this product yourself, as opening or removing covers may expose you to
dangerous voltage potentials and risk of electric shock.
• Refer all servicing to qualified service personnel.
• Attempts to alter the factory-set internal controls or to change other control settings not specially discussed
in this manual can lead to permanent damage to the projector and cancellation of the warranty.
• Remove all power from the projector and refer servicing to qualified service technicians under the following
conditions:
- When the power cord or plug is damaged or frayed.
- If liquid has been spilled into the equipment.
- If the product has been exposed to rain or water.
- If the product does not operate normally when the operating instructions are followed. Adjust only those
controls that are covered by the operating instructions since improper adjustment of the other controls
may result in damage and will often require extensive work by a qualified technician to restore the
product to normal operation.
- If the product has been dropped or the cabinet has been damaged.
- If the product exhibits a distinct change in performance, indicating a need for service.
• Replacement parts: When replacement parts are required, be sure the service technician has used original
Barco replacement parts or authorized replacement parts which have the same characteristics as the
Barco original part. Unauthorized substitutions may result in degraded performance and reliability, fire,
electric shock or other hazards. Unauthorized substitutions may void warranty.
• Safety check: Upon completion of any service or repairs to this projector, ask the service technician to
perform safety checks to determine that the product is in proper operating condition.
Safety Data Sheets for Hazardous Chemicals
For safe handling information on chemical products, consult the Safety Data Sheet (SDS). SDSs are available
upon request via safetydatasheets@barco.com.
1.3 Product safety labels
Light beam related safety labels for G60-W7 series
Label image Label description
Risk Group 2 of IEC60825-1:2014 and Class 3R Laser product of
IEC 60825-1:2007. Do not look into the laser light. The extremely
high brightness may cause permanent eye damage.
COMPLIES WITH
21 CFR 1040.10 AND
1040.11 E
XCEPT FOR
DEVIATIONS PURSUANT
TO LASER NOTICE No. 50,
DATED JUNE 24, 2007.
IEC/EN 60825-1:2007
IEC/EN 60825-1 : 2007
LASER RADIATION -AVOID DIRECT EYE EXPOSURE - CLASS 3R LASER PRODUCT
Wave length : 449-461 nm / Max. Pulse energy : 0.52mJ / Pulse duration : 1.06 ms
IEC/EN 60825-1 : 2014 CLASS 1 LASER PRODUCT / RISK GROUP 2
WARNING : Possibly hazardous optical radiation emitted from this product.
Do not stare into the beam, May be harmful to the eyes.
IEC/EN 60825-1 : 2007
IEC/EN 60825-1 : 2014
IEC/EN 60825-1 : 2007
RAYONNEMENT LASER - ÉVITEZ TOUTE EXPOSITION DIRECTE DES YEUX -
PRODUIT LASER DE CLASSE 3R
Longueur d'ondes : 449 - 461 nm / Max.impulsion d'énergie : 0.52 mJ /
Durée impulsions 1.06 ms
IEC/EN 60825-1 : 2014 PRODUIT LASER DE CLASSE 1 / GROUPE A RISQUE 2
AVERTISSEMENT : Risquse possibles de rayonnements optiques émis par ce produit.
Ne pas regarder dans le faisceau. Peut être dangereux pour les yeux.
IEC/EN 60825-1 : 2007
IEC/EN 60825-1 : 2014
This product is classified as Class 1 Laser Product-Risk Group 2 of
IEC 60825-1 : 2014 and Class 3R Laser product of IEC 60825-
1:2007, complying with 21 CFR 1040.10 and 1040.11 except for
deviations pursuant to Laser Notice No.50, dated June 24, 2007.
Safety
To Next Page
Loading...
