Barco RLM W6 - User Manual

Other manuals for Barco RLM W6

Service Manual133 pages

Questions and Answers

E
Emily ParkerAug 20, 2025
How to fix Barco RLM W6 remote control that does not operate normally?
- T
  Terrence JohnsonAug 20, 2025
  If the Barco Projector remote control isn't working, there could be several reasons. The battery might be dead, so try replacing it with a new one, ensuring correct orientation. You might be too far from the projector's IR sensor or at an extreme angle; adjust your position. Obstacles or intense light near the sensor could also interfere. Check for and remove any wired remote connected to the 3.5mm port, or use the wired remote for operation. Finally, the remote control's address may not match the projector's; press the ENTER button followed by the Address button until the panel flashes once.
M
Makayla OconnellAug 22, 2025
What to do if my Barco Projector cannot be turned on?
- A
  Anthony LeonardAug 22, 2025
  If your Barco Projector won't turn on, ensure the power cord is plugged into a working wall outlet and the power switch is flipped to "I". Also, make sure the lens cover has been properly replaced.
C
Casey KennedyAug 25, 2025
Why is my Barco RLM W6 Projector picture blurry?
- D
  Diana BaldwinAug 25, 2025
  If the image on your Barco Projector is blurry, try adjusting the lens focus. If that doesn't work, it could be due to changes in temperature or humidity. Turn off the projector and allow time for any moisture inside to evaporate.
M
martinezchloeAug 27, 2025
Why is my Barco RLM W6 Projector image flashing occasionally?
- N
  Nancy KnightAug 27, 2025
  If the image on your Barco Projector flashes occasionally, ensure the cables are properly connected and the input device is working correctly. If the problem persists, the lamp might be faulty and need replacement.
D
donald49Aug 28, 2025
Why does my Barco RLM W6 Projector picture look dim?
- T
  twardAug 28, 2025
  If the picture on your Barco Projector looks dim, try adjusting the image brightness, contrast, color, and tint. If the issue persists, the projector lamp may need to be replaced.
C
cory24Aug 30, 2025
What to do if my Barco RLM W6 cannot be turned on after turning it off?
- F
  Fernando FordAug 30, 2025
  If you cannot turn on your Barco Projector after turning it off, wait for the projector to cool down completely before starting it up again.
J
John LeonardSep 1, 2025
Why is my Barco RLM W6 Projector image too bright or blurry?
- D
  Daniel WhiteSep 1, 2025
  If the image from your Barco Projector is too bright or the bright areas are blurry, the contrast might be set too high. Try lowering the contrast settings.
J
Jacqueline KlineSep 3, 2025
Why is my Barco RLM W6 Projector image washed out?
- C
  Carol JonesSep 3, 2025
  If the image on your Barco Projector appears washed out, or the dark areas appear too bright, the image brightness might be set too high. Lower the brightness settings.
K
Krista CampbellSep 5, 2025
Why does the LED indicator on the rear panel of my Barco Projector blink in red?
- N
  Nicholas JohnsonSep 5, 2025
  If the LED indicator on the rear panel of your Barco Projector is blinking red, the lamp might be damaged and needs replacement, as it has likely reached the end of its service life.
B
Barry WatsonSep 7, 2025
Why does my Barco RLM W6 lamp not turn on?
- C
  Clinton WestSep 7, 2025
  If the lamp in your Barco Projector does not turn on even when the projector is on, the lamp might be damaged and needs replacement, as it has likely reached the end of its service life.

Summary

Warning, Notices and Safety Instructions

Notice and Accessories

Basic information, serial number, and check included accessories.

FCC and Regulatory Compliance

Details on FCC rules and Canadian standards.

General Safety Warnings

Laser, sun, electric shock, and power cord safety.

Installation Environment and Safety

Pre-installation checks, lamp safety, and installation site.

Product Material Content

Toxic and hazardous substances information.

Projector Parts and Functions

Front and Rear Views

Identification of components on the front and rear panels.

Input;Output Ports Identification

Details all available connection interfaces on the projector.

Bottom View and Mounting

Information on bottom mounting holes and dimensions.

Remote Control Operation

Effective signal reception range and battery installation.

Quick Installation of the Projector

Initial Setup and Connections

Orienting, connecting power/PC, and removing lens cover.

Projector Angle and Lens Adjustments

Adjusting feet, lens shift, focus, and zoom.

Image Correction and Shutdown

Correcting keystone and proper projector shutdown.

Installing the Projector

Throw Distance and Installation Modes

Explains throw ratio, lens options, and environmental considerations.

Projection Setup Types

Details frontal, rear, and ceiling projection configurations.

Lens Shift Adjustment

In-depth explanation of lens shift capabilities and adjustment.

Input Connections

Guide for connecting HDMI, DVI, 12V Trigger, and other devices.

OSD Settings and Screen Orientation

Changing menu language and setting projection modes.

Using the Remote Control

Remote Control Overview and Input Selection

Explains button functions for input selection and basic operations.

Image Adjustment Functions

Details buttons for contrast, brightness, sharpness, color, and tint.

Special Function Buttons

Explains PIP, SWAP, and ADDRESS functions.

OSD Menu Description

OSD Menu Navigation

How to access and navigate the OSD menu system.

Input and Image Settings

Configuring input sources, video standards, and image parameters.

Lamp and Control Settings

Configuring lamp modes, fan speed, projector controls, and network.

Service Menu Information

Accessing projector status, performing resets, and troubleshooting data.

Lamp and Filter Maintenance

Lamp Replacement Procedure

Step-by-step guide for replacing the projector lamp.

Cleaning the Projector Filter

Instructions for cleaning the dust filter and ventilation slots.

Troubleshooting and LED Indicators

Common Projector Problems and Solutions

Table of issues and recommended troubleshooting steps.

LED Status Indicator Definitions

Explanation of projector status based on LED color and flashing.

Projector Specifications

General Specifications

Brightness, resolution, lamp type, power consumption, and dimensions.

Input;Output Port Compatibility

Table detailing supported signal types and resolutions.

Physical Dimensions and Diagrams

Technical drawings showing projector measurements.

Barco RLM W6 Specifications

General

Matrix size	0.67 \
Heat dissipation	2900 BTU/h
Projection distance	- m
Projection technology	DLP
Contrast ratio (dynamic)	3000:1
Contrast ratio (typical)	2200:1
Digital gamma correction	Yes
Screen size compatibility	- \
Projector native resolution	WUXGA (1920x1200)
Aspect ratio	16:10
RS-232 ports	1
Dimensions (WxDxH)	516.7 x 669.74 x 247 mm
Maximum analog resolution	1600 x 1200 pixels
Maximum digital resolution	1920 x 1200 pixels
Focal length range	- mm
Vertical lens shift range	0 - 100 %
Horizontal lens shift range	-30 - 30 %
Lamp power	330 W
Lamps quantity	2 lamp(s)
Light source type	Lamp
Service life of light source	1500 h
Service life of light source (economic mode)	2000 h
Noise level	39 dB
Preset modes	sRGB, Standard
Certification	FCC, CE EN55022 Cl. A, CE, TUV, WEEE.
Dot clock scanning frequency	165 MHz
Full HD	No
Analog signal format system	NTSC
Supported graphics resolutions	1600 x 1200 (UXGA), 1920 x 1200 (WUXGA)
BNC input ports	5
Serial interface type	RS-232
USB 2.0 ports quantity	0
Ethernet LAN data rates	10, 100 Mbit/s
Placement	Desktop, Ceiling
Product type	Large venue projector
Product color	Black
Market positioning	Presentation
Power source	AC
AC input frequency	50 - 60 Hz
Power consumption (standby)	2 W
Power consumption (typical)	850 W
Operating temperature (T-T)	0 - 40 °C
Operating relative humidity (H-H)	0 - 80 %
Cables included	AC, HDMI-DVI
Remote control type	IR
Sustainability certificates	RoHS