EasyManuals Logo
Home>BendPak>Lifting Systems>XPR-9 Series

BendPak XPR-9 Series User Manual

BendPak XPR-9 Series
92 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #2 background imageLoading...
Page #2 background image
Manual. XPR-9 Series Two-Post Lifts, Installation and Operation Manual, Manual Part Number 5900371, Manual
Revision D2, released May 2023.
Copyright. Copyright © 2023 by BendPak Inc. All rights reserved. You may make copies of this document if you
agree that: full attribution goes to BendPak Inc., you are not authorized to make changes to the content, you do
not gain any rights to this content, and you will not use the copies for commercial purposes.
Trademarks. BendPak and the BendPak logo are registered trademarks of BendPak Inc. All other company,
product, and service names are used for identification only. All trademarks and registered trademarks mentioned
in this manual are the property of their respective owners.
Limitations. Every effort has been made to ensure complete and accurate instructions are
included in this manual. However, product updates, revisions, and/or changes may have
occurred since this manual was published. BendPak reserves the right to change any
information in this manual without incurring any obligation for equipment previously or
subsequently sold. All drawings are reference only – do not scale. BendPak is not responsible
for typographical errors in this manual. You can always find the latest version of the manual
for your product on the BendPak website.
Warranty. The BendPak warranty is more than a commitment to you: it is also a commitment
to the value of your new product. Contact your nearest BendPak dealer or visit
www.bendpak.com/support/warranty for full warranty details. Go to bendpak.com/support/register-
your-product/ and fill out the online form to register your product (be sure to click Submit).
Safety. Your Lift was designed and manufactured with safety in mind. Your safety also depends on proper
training and thoughtful operation. Do not set up, operate, maintain, or repair the Lift without reading and
understanding this manual and the labels on the unit; do not use your Lift unless you can do so safely!
Owner Responsibility. In order to maintain your product properly and to ensure operator safety, it is the
responsibility of the product owner to read and follow these instructions:
Follow all installation, operation, and maintenance instructions.
Make sure product installation conforms to all applicable local, state, and federal codes, rules, and regulations,
such as state and federal OSHA regulations and electrical codes.
Read and follow all safety instructions. Keep them readily available for operators.
Make sure all operators are properly trained, know how to safely operate the unit, and are properly supervised.
Do not operate the product until you are certain all parts are in place and operating correctly.
Carefully inspect the product on a regular basis and perform all maintenance as required.
Service and maintain the unit only with approved replacement parts.
Keep the manual with the product and make sure all labels are clean and visible.
BendPak makes no promises, guarantees or assurances that our products meet any state, county, federal or
international mandated permit, license, code, standard, certification, or any other mandate other than what is
listed or shown on BendPak website(s), or any BendPak online or published catalog. Not all BendPak lift
models meet the standards as prescribed by ANSI/ALI ALCTV-(current edition) or ANSI/UL 201. Consult
www.autolift.org for a complete list of lift models that meet ANSI/ALI ALCTV-(current edition) or ANSI/UL
201, or contact BendPak via www.bendpak.com/contact/ Buyer assumes full responsibility for
any state, county, federal or international mandated permit, license, code, standard,
certification, or any other mandate required related to the installation and/or operation of
any BendPak or Autostacker product. BendPak will not be responsible for any charges, fines, liens, or
other levies imposed on the Buyer related to any special or regional structural, seismic or any other building
code and/or codes such as the Uniform Building Code (UBC), International Building Code (IBC), or any other
state, county, federal or international mandated permit, license, code, standard, certification, or other
mandate, law, rule, regulation or directive by any other agency, government, administrations, or corporations
whether state, county, federal, or international mandated.
Only use the Lift if it can be used safely!
SCANFOR
DIGITIALPDF

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the BendPak XPR-9 Series and is the answer not in the manual?

BendPak XPR-9 Series Specifications

General IconGeneral
BrandBendPak
ModelXPR-9 Series
CategoryLifting Systems
LanguageEnglish

Related product manuals