Binder KB 115 (E4) - KB 400 Dimensions

149 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

KB (E4 + E6) 02/2017 page 136/148

23.10 KB 400 dimensions

[mm]

Table of Contents

Default Chapter2
- Table of Contents2
1 Safety6
- Legal Considerations6
- Structure of the Safety Instructions6
- Localization / Position of Safety Labels on the Chamber8
- Type Plate9
- General Safety Instructions on Installing and Operating the Chambers10
- Intended Use12
- Operating Instructions12
- Measures to Prevent Accidents13
2 Chamber Description14
- Chamber Overview15
- Instrument Panel16
- Lateral Control Panel with Main Power Switch and Optional Equipment - KB 240 / 400 / 720 (E6)17
- Chamber Rear - KB 53 / 115 (E4)18
3 Completeness of Delivery, Transportation, Storage, and Installation19
- Unpacking, and Checking Equipment and Completeness of Delivery19
- Guidelines for Safe Lifting and Transportation20
- Storage20
- Location of Installation and Ambient Conditions21
4 Installation of the Equipment22
- Spacers for Wall Distance - KB 240 / 400 / 720 (E6)22
- Mounting the Flexible Tilt Protection Kit - KB 400 (E6)23
- Electrical Connection24
5 Start up25
6 Functional Overview of the T4.12 Chamber Controller25
- Menu Structure26
- Operating Modes29
  - Activating the "Control Off" Mode or Change to "Fixed Value" Operating Mode29
- Performance During and after Power Failure31
- Information32
7 Configuration of Optional Equipment33
- Turning on / off the Optional Interior Socket33
- Switching on or off the Optional Zero-Voltage Relay Control Outputs34
- Functional Test of the Optional Alarm Output34
- Switching on or off the Optional Object Temperature Display35
- RS 422 Address (with Optional RS 422 Interface)35
8 Set-Point Entry in "Fixed Value" Operating Mode36
- Setting Ranges36
- Entering the Set-Points Via "Quick Menu36
- Entering the Set-Points Via General Menu38
9 Time Programs40
- Starting and Running an Existing Time Program42
- Cancelling a Running Time Program45
- Creating a New Time Program46
- Program Interruption60
- Deleting a Time Program61
10 Week Programs62
- Starting and Running an Existing Week Program63
- Cancelling a Running Week Program66
- Creating a New Week Program67
- Deleting a Week Program76
11 Key Lock77
- Directly Activating the Key Lock Function78
- Automatic Key Lock78
- Changing the Password for Unlocking the Key Lock80
12 General Controller Settings81
- Setup Wizard82
- Date and Time Settings82
- Selecting the Menu Language of the T4.12 Controller84
- Setting Display Brightness84
- Changing the Temperature Unit85
- Defining the Data Recording Rate85
- Factory Reset86
- Network Configuration86
- Display of the Entire Network Configuration90
- Display and Entry of the Chamber Configuration - for Service Purpose90
13 Data Transfer Via Usb Interface91
- Exporting Data to USB Drive91
- Importing Data from USB Drive92
14 Notifications and Alarms93
- Notifications Overview93
- Alarms Overview93
- Alarm Status94
- Confirming a "Set" Alarm95
- Alarm Configuration and Overview96
15 Event List99
16 Graphical Display of the Measured Values100
- Setting the Sampling Rate100
- Defining the Display Range101
- Selecting the Parameters102
17 Temperature Safety Devices103
- Over Temperature Protective Device (Class 1)103
- Overtemperature Safety Controller (Temperature Safety Device Class 3.1)103
  - Safety Controller Modes103
  - Setting the Safety Controller104
- Over- and Undertemperature Safety Controller (Temperature Safety Device Class 3.3) (Option)107
  - Safety Controller Modes107
  - Setting the Over- and Undertemperature Safety Controller108
18 Defrosting During Refrigerating Operation111
19 Options112
- Communication Software APT-COM™ 3 Datacontrolsystem (Option)112
- RS RS 422 Interface (Option)112
- Data Logger Kit (Option)112
- Object Temperature Display with Flexible Pt 100 Temperature Sensor (Option)113
- Zero-Voltage Relay Alarm Output (May be Available Via BINDER INDIVIDUAL Customized Solutions)113113
- Analog Output for Temperature (Option)115
- Zero-Voltage Relay Control Outputs (May be Available Via BINDER INDIVIDUAL Customized Solution)115
- Water Protected Internal Socket (Option)116
- Interior Lighting116
20 Maintenance, Cleaning, and Service117
- Maintenance Intervals, Service117
- Cleaning and Decontamination118
  - Cleaning118
  - Decontamination119
- Sending the Chamber Back to BINDER Gmbh120
21 Disposal121
- Disposal of the Transport Packing121
- Decommissioning121
- Disposal of the Chamber in the Federal Republic of Germany121
- Disposal of the Chamber in the Member States of the EC Except for the Federal Republic of Germany123
- Disposal of the Chamber in Non-Member States of the EC124
22 Troubleshooting125
23 Technical Description127
- Factory Calibration and Adjustment127
- Over Current Protection127
- Definition of Usable Volume128
- Technical Data129
- Equipment and Options (Extract)131
- Spare Parts and Accessories (Extract)132
- KB 53 Dimensions133
- KB 115 Dimensions134
- KB 240 Dimensions135
- KB 400 Dimensions136
- KB 720 Dimensions137
24 Certificates and Declarations of Conformity138
- EU Declaration of Conformity138
  - Certificate for the GS Mark of Conformity of the "Deutsche Gesetzliche Unfallversicherung E.V." (German Social Accident Insurance) DGUV140
25 Product Registration142
26 Contamination Clearance Certificate143
- For Chambers Located Outside USA and Canada143
- For Chambers in USA and Canada146

Related product manuals

Preview: Binder KB 53 (E4)

Binder KB 53 (E4)

Preview: Binder KB

Binder KB 240 (E6)

Binder KB 400 (E6)

Binder KB 720 (E6)

Binder KB 240-UL (E6)

Binder KB 400-UL (E6)

Preview: Binder APT.line KB Series

Binder APT.line KB Series

Binder BF 115-UL

Binder APT.line KT 53

Binder APT.line FD 53-UL