Blodgett Mark V Installation & Operation Manual

Operation
17
Blodgett IQT Phase IV Control
2ND LEVEL PROGRAMMING
Entering the programming mo de
1. Press the PROG KEY (10). The top display
reads CodE.
2. Use the product keys to enter the program-
ming access code: 4 5 1 2. Press t he ENTER
KEY (14). The top display reads SYS.
Programming hold
Hold allows product to be kept warm in the oven
at a programmed time and temperature. There are
two hold modes available, auto and manual. If
auto hold is enabled the control will automatically
place the oven into the hold mode at the end of
each cooking cycle. If manual hold is enabled the
unit can be placed into the hold mode at any time.
1. Press the SCAN KEY (15). The top display
reads Hold. Press the TOGGLE/CLEAR KEY
(11) to toggle between YES and no.Pressthe
SCAN KEY (15).
If no is chosen:
a.) The controller advances to programming
the setback mode.
Ifyesischosen:
a.) The top display reads AUTO.Pressthe
TOGGLE/CLEAR KEY (11) to toggle be-
tween YES and no. Press the SCAN KEY
(15) to enter t he desired hold mode.
b.) The top display reads HOLD. The bottom
display gives the current hold time. Press
the TOGGLE/CLEAR KEY (11). Use the
product keys to enter a hold time from 0
to 9 hours. Press the SCAN KEY (15) to
enter the new hold time.
c.) The top display reads HOLD. The bottom
display gives the current hold tempera-
ture. Press the TOGGLE/CLEAR KEY (11).
Use t he product keys t o enter a hold tem-
perature from 140_F --- 2 1 0 _F. P r e s s t h e
SCAN KEY (15) to enter the new hold tem-
perature.
d.) The top display reads FAn. The bottom
display gives the current fan mode. To
change the fan mode press the TOGGLE/
CLEAR KEY (11). The bottom display
toggles between Hi and Lo.Pressthe
SCAN KEY (15) to enter the new fan mode
and continue with programming the s et-
back mode.
Programming the setback mode
The setback mode operates as a power saving
feature. After a period of non-use (the setback
time) t he oven temperature automatically de-
creases to the setback temperature. The oven will
maintain this temperature until a product key is
pressed.
1. The top display reads SEtb. The bottom dis-
play gives the setback mode. To change the
setback press the TOGGLE/CLEAR KEY (11).
The bottom display toggles between YES and
no. Press the SCAN K EY (15).
If no is chosen:
a.) The controller advances to programming
the temperature mode.
Ifyesischosen:
a.) The bottom display gives the current set-
back time. Press the TOGGLE/CLEAR
KEY (11). U se the product keys to the en -
ter t he desired setback time. Press the
SCAN KEY (15) to enter the new setback
time.
NOTE: The minimum setback time is 20:00.
The maximum setback time is 59:59.
b.) The bottom display gives the current set-
back temperature. Press the TOGGLE/
CLEAR KEY (11). Use the product keys to
the enter a setback temperature from
140_F --- 3 0 0 _F. Press the SCAN KEY (15)
to enter the new setback and continue
with programming the temperature
mode.
Programming the temperature mode (_For_C)
1. The top display reads dEg. The bottom dis-
play gives the units. To change the units press
the TOGGLE/CLEAR KEY (11). The bottom
display toggles between F and C.
2. Press the SCAN KEY (15) to enter the new
temperature units and continue programming
the oven size.

Blodgett Mark V Specifications

General

Model	Mark V
Manufacturer	Blodgett
Category	Oven
Temperature Range	200°F - 500°F (93°C - 260°C)
Construction	Stainless Steel