Bosch D6412 - Page 4

D6412/D4412 Operation and Installation Guide
Page 4 © 2003 Bosch Security Systems45349E
D6412/D4412
Contents
10.2.2 Configuring the DX3010 Octo-Output Module .......................................................................................................... 41
10.2.3 Relay Outputs ...................................................................................................................................................................... 41
10.2.4 Installation ............................................................................................................................................................................. 42
10.2.5 DX3010 to D6412/D4412 SDI Bus Wiring Connections ....................................................................................... 42
10.2.6 Address Programming ........................................................................................................................................................ 44
11.0 Arming Devices ................................................................................................................................................................................... 45
11.1 Description ........................................................................................................................................................................... 45
11.2 Command Centers ............................................................................................................................................................ 45
11.2.1 Assigning the Command Center an Address .............................................................................................................. 45
11.2.2 Command Center Installation .......................................................................................................................................... 46
11.3 D268/D269, D279 Independent Zone Control ......................................................................................................... 47
11.4 Keyswitch .............................................................................................................................................................................. 47
11.4.1 Keyswitch Description ....................................................................................................................................................... 47
11.4.2 Keyswitch Programming .................................................................................................................................................... 47
11.4.3 Keyswitch Installation ........................................................................................................................................................ 48
11.4.4 Keyswitch Operation .......................................................................................................................................................... 48
12.0 SDI Devices .......................................................................................................................................................................................... 49
12.1 Description ........................................................................................................................................................................... 49
12.2 Installation ............................................................................................................................................................................ 49
12.3 DX4010 RS-232 Serial Interface Module .................................................................................................................. 50
12.3.1 DX4010 Installation ............................................................................................................................................................ 50
12.3.2 DX4010 to D6412/D4412 SDI Bus Wiring Connections ....................................................................................... 51
12.3.3 RAM IV Direct Connection ............................................................................................................................................... 51
12.3.4 Configuration Jumpers ....................................................................................................................................................... 52
12.3.5 Supervision ........................................................................................................................................................................... 52
12.3.6 DX4010 Module’s DB9 Connector ................................................................................................................................ 52
13.0 Installer’s Keypad and Installer Mode .................................................................................................................................... 53
13.1 Installer’s Keypad Connector .......................................................................................................................................... 53
13.2 Entering the Installer Mode ............................................................................................................................................. 53
13.2.1 Installer’s Passcode ............................................................................................................................................................ 53
13.2.2 Service Start/Service End Reports ................................................................................................................................ 54
13.3 Installer’s Menu .................................................................................................................................................................. 54
13.3.1 Press [1] for Bell Test ......................................................................................................................................................... 54
13.3.2 Press [2] for Strobe Test ................................................................................................................................................... 54
13.3.3 Press [3] for Battery Test .................................................................................................................................................. 54
13.3.4 Press [4] for Test Report ................................................................................................................................................... 54
13.3.5 Press [5] for Point Status ................................................................................................................................................. 54
13.3.6 Press [6] for Output Test .................................................................................................................................................. 55
13.3.7 Press [7] for RF Menu ....................................................................................................................................................... 55
13.3.8 Press [8] for Keypad Program ......................................................................................................................................... 56
13.3.9 Press [9] Program Key ....................................................................................................................................................... 57
13.3.10 Exiting the Installer’s Menu .............................................................................................................................................. 58
13.3.11 Press [0] Call for Service Details ................................................................................................................................... 58
14.0 Installation Label ................................................................................................................................................................................ 59
15.0 Terminal Quick Reference ............................................................................................................................................................. 61
16.0 Troubleshooting ................................................................................................................................................................................. 63
16.1 Introduction .......................................................................................................................................................................... 63
16.1.1 Arming Issues ....................................................................................................................................................................... 63
16.1.2 Point Issues .......................................................................................................................................................................... 63
16.1.3 Command Center Issues .................................................................................................................................................. 64
16.1.4 Programming Issues ........................................................................................................................................................... 64
16.1.5 Miscellaneous Issues ......................................................................................................................................................... 64