Bosch D6412 - Page 6

D6412/D4412 Operation and Installation Guide
Page 6 © 2003 Bosch Security Systems45349E
D6412/D4412
Figures
Figures
Figure 1: System Configuration ...................................................................................................................................................... 10
Figure 2: Enclosure Mounting ......................................................................................................................................................... 16
Figure 3: Installer Switch .................................................................................................................................................................. 16
Figure 4: System Status LED ......................................................................................................................................................... 20
Figure 5: On-Board Outputs ........................................................................................................................................................... 22
Figure 6: RJ31X/RJ38X Wiring ...................................................................................................................................................... 23
Figure 7: Ground Start ...................................................................................................................................................................... 25
Figure 8: Typical Two-Wire Smoke Detector Wiring ................................................................................................................. 27
Figure 9: Typical Four-Wire Smoke Detector Wiring ................................................................................................................ 27
Figure 10: Sensor Loop 1 Wiring ................................................................................................................................................... 28
Figure 11: Single Point Sensor Loop Wiring .............................................................................................................................. 28
Figure 12: On-Board Doubled Point Sensor Loop Wiring ....................................................................................................... 29
Figure 13: Installing the DX2010 in D203 Enclosure .............................................................................................................. 33
Figure 14: Installing the DX2010 in the Panel Enclosure ....................................................................................................... 33
Figure 15: Optional Enclosure Mounting Locations for the DX2010 ................................................................................... 34
Figure 16: Wiring the DX2010 to the D6412/D4412 .............................................................................................................. 35
Figure 17: Wiring the DX2010 for External Power Supply ...................................................................................................... 35
Figure 18: Auxiliary Output Connections ..................................................................................................................................... 36
Figure 19: DX2010 Tamper Input Wiring ..................................................................................................................................... 36
Figure 20: DX2010 Sensor Loop Wiring, Single Loop Configuration ................................................................................. 37
Figure 21: DX2010 Sensor Loop Wiring, Doubled Loop Configuration .............................................................................. 37
Figure 22: DX2010 DIP Switch Configuration ........................................................................................................................... 38
Figure 23: DX2010 Status LED ..................................................................................................................................................... 38
Figure 24: PO1 Wiring ..................................................................................................................................................................... 39
Figure 25: PO2-PO4 Wiring ........................................................................................................................................................... 39
Figure 26: DX3010 - Control Panel Enclosure Side Mounting ............................................................................................. 42
Figure 27: Installing the DX3010 in a Remote Enclosure ....................................................................................................... 42
Figure 28: Wiring the DX3010 to the D6412/D4412 .............................................................................................................. 43
Figure 29: Wiring for External Power Supply .............................................................................................................................. 43
Figure 30: DX3010 Address DIP Switches ................................................................................................................................. 44
Figure 31: Command Center DIP Switch Orientation ............................................................................................................. 45
Figure 32: Wiring Command Centers to the D6412/D4412 ................................................................................................. 46
Figure 33: External Power for Command Centers ..................................................................................................................... 47
Figure 34: Keyswitches ..................................................................................................................................................................... 48
Figure 35: SDI Device Wiring ......................................................................................................................................................... 49
Figure 36: External Power for SDI Devices ................................................................................................................................. 50
Figure 37: DX4010 RS-232 Serial Interface Module .............................................................................................................. 50
Figure 38: DX4010 Power Connections ...................................................................................................................................... 51
Figure 39: Creating a RAM IV Direct Connection .................................................................................................................... 51
Figure 40: DX4010 P2/P3 Jumper Pin Settings ........................................................................................................................ 52
Figure 41: DX4010 DIP Switch Orientation ............................................................................................................................... 52
Figure 42: DX4010 D89 Connector Layout ............................................................................................................................... 52
Figure 43: Installer’s Keypad ........................................................................................................................................................... 53
Figure 44: Installer Switch ............................................................................................................................................................... 54
Figure 45: Adding RF ID Codes Menu Display .......................................................................................................................... 55
Figure 46: RF ID Code Display ...................................................................................................................................................... 55
Figure 47: Test RF Devices Display ............................................................................................................................................... 55
Figure 48: RF Device Test Status Display ................................................................................................................................... 55
Figure 49: RF ID Code Display ...................................................................................................................................................... 56
Figure 50: PK32 to D6412/D4412 Connections ...................................................................................................................... 57