How to fix no network connection on Bosch MIC IP ultra 7100i Security Camera?
If you have no network connection with your Bosch Security Camera, check all network connections and ensure that the maximum distance between any two Ethernet connections is 100 m (328 ft) or less. If you are behind a firewall, ensure that the Video Transmission mode is set to UDP.
Why does my Bosch IP Camera reboot frequently?
Frequent or intermittent reboots of your Bosch IP Camera can occur due to an improper network connection. To resolve this, test the camera with another power supply. Also, check the Bosch website for a software update that might address the issue.
What to do if “High Shock Event” appears on my Bosch MIC IP ultra 7100i?
If the Bosch Security Camera experienced a high shock event, inspect the mechanical parts and screws, especially on the yoke arms. If there's severe damage, discontinue use and contact the Bosch Service Center. If no damage is visible, either cycle the power on the camera or send the command AUX OFF 65 to remove the OSD message.
Why does my Bosch MIC IP ultra 7100i Security Camera reboot frequently?
To resolve frequent or intermittent reboots of your Bosch Security Camera, try testing it with another power supply. Also, check the Bosch website for a software update that might address the issue, as the problem may stem from an improper network connection.
Why is there no video on my Bosch MIC IP ultra 7100i?
If your Bosch Security Camera is not showing any video, verify that the main power to the power supply is on. For IP-enabled cameras, check if you can access a web page. If you can, try cycling the camera's power off and on. If not, you might have the wrong IP address; use Configuration Manager to identify the correct IP address. Also, ensure there is a 24 V output from the transformer and check the integrity of all wires and mating connectors to the camera.
Why is the picture dark on my Bosch Security Camera?
If the picture on your Bosch Security Camera is dark, ensure that the Gain Control is set to High, the Auto Iris Level is set to the appropriate level, and the maximum Ethernet cable distance has not been exceeded. If these settings are correct, try restoring all camera settings.
Why does my Bosch Security Camera move when trying to control other cameras?
If your Bosch Security Camera moves when attempting to move other cameras, check that the camera’s IP address is properly set. Use Configuration Manager to confirm that two cameras do not have the same IP address, and if they do, change the address of one of the cameras.
What to do if Bosch MIC IP ultra 7100i Security Camera doesn't work after extreme cold?
If your Bosch Security Camera does not operate at all, or does not operate as expected, after being subjected to extreme low temperatures (below -40 ° (-40 °F)), allow the camera to warm up for 60 minutes prior to PTZ operations. If the camera still does not operate after this warm-up period, reset the camera by typing “/reset” at the end of the IP address of the camera in your web browser.
How to fix no camera control on Bosch MIC IP ultra 7100i?
If you have no camera control on your Bosch Security Camera, ensure that the LAN cable has a secure connection. Refresh the browser and ensure that the video is updated. Also, cycle the camera's power off and on.
How to resolve a distorted image on Bosch MIC IP ultra 7100i?
To resolve a distorted image on the screen of your Bosch Security Camera, set the synchronization mode to INT. if the power frequency is not set correctly and the line lock synchronization mode cannot be used. (NTSC Model power frequency in LL mode: 60 Hz.)
General| Camera Type | PTZ |
|---|---|
| Weather Resistance | Yes |
| Power Consumption | 60 W max |
| Video Compression | H.265, H.264, MJPEG |
| Pan Range | 360° continuous |
| Lens Type | Varifocal |
| IP Rating | IP68 |
| Resolution | 4K Ultra HD (3840 x 2160) |
| Power | High PoE (60 W) |
| Frame Rate | 30 fps |
| Day/Night | True Day/Night |
| Operating Temperature | -40°C to +65°C |
Steps to connect the camera to the network and access it.
Setting and managing passwords for device security and access.
Managing user accounts, authorization levels, and passwords.
Accessing camera settings for installation and basic configuration.
Defining and managing video encoding profiles for optimal transmission.
Configuring multiple video streams with different profiles and settings.
Configuring pan, tilt, zoom, and movement behaviors.
Defining and managing saved camera positions and automated tours.
Managing storage devices like iSCSI and SD cards.
Adding, activating, and configuring storage media for recordings.
Configuring how the camera responds to alarms and connects to IP addresses.
Overview of VCA settings, profiles, scenarios, and analysis types.
Defining rules to trigger camera responses based on specific inputs.
Integrating the camera into a network, including IP and MAC address setup.
Updating firmware, viewing upload history, and managing configuration files.
Controls for viewing camera streams (Stream 1, 2, M-JPEG).
Accessing, searching, and exporting recorded video.
Lists common problems and recommended actions for resolution.
Identifies camera status codes, descriptions, and recommended actions.
To Next Page
