What to do if the Bosch Iron steam generator does not come on?
If the steam generator does not come on, first check the mains cable, the plug, and the socket to ensure there are no connection problems. Also, make sure that the main power button is set to the “I” position, so that it is illuminated in red.
Why am I experiencing loss of pressure during ironing with my Bosch Iron?
If you experience a loss of pressure during ironing with your Bosch Iron, it might be because the steam release button is activated for too long. Use the steam release button at intervals to allow the textiles to dry and stay smooth better.
Why does my Bosch Iron leak water through the soleplate?
Water flowing through the holes of the soleplate of your Bosch iron can occur because the steam function is being used before the iron has reached the correct temperature, or water is condensing inside the pipes from infrequent use. To resolve this, reduce the steam flow when ironing at low temperatures. You can also point the iron away from the ironing area and press the steam release button until steam is produced.
Why do water spots appear on the garment during ironing with my Bosch Sensixx B45L?
If water spots appear on the garment during ironing with your Bosch Iron, it may be caused by steam condensed on the ironing board. Wipe the textile cover of the ironing board and iron the spots without steam to dry them.
Why does the steam generator of my Bosch Sensixx B45L Iron not come on?
If your Bosch Iron steam generator does not come on, check the mains cable, plug, and socket for connection problems. Also, make sure the main power button is set to the “I” position (illuminated in red).
Why is my Bosch Sensixx B45L Iron display not reacting to touch?
If the display of your Bosch iron does not react when touched, clean it with a damp cotton fabric (not too wet). You might also need to warm your fingers a little bit and try again.
Why is water flowing through the holes on the soleplate of my Bosch Sensixx B45L Iron?
If your Bosch Iron is leaking water through the soleplate, it could be due to several reasons. First, the steam function might be used before the iron has reached the correct temperature; try reducing the steam flow when ironing at low temperatures. Second, water might be condensing inside the pipes, especially if steam is being used for the first time or after a long period; point the iron away from the ironing area and press the steam release button until steam is produced. Finally, the steam generator may contain too much scale; clean the boiler as described in section “Calc’n’Clean Advanced” (F).
How to fix Bosch Sensixx B45L not producing steam?
If your Bosch iron is not producing steam, it could be due to a couple of reasons. First, check if the boiler is switched on (the main power button should be set to the “I” position and illuminated in red) and ensure the water tank is not empty. If both are fine, then check if the steam regulation is set to the minimum position. If so, increase the steam flow.
Why does my Bosch Sensixx B45L Iron not heat up?
If your Bosch Iron does not heat up, ensure that the main power button is set to the “I” position, so that it is illuminated in red. Also, check that the temperature is set to the desired position.
What to do if my Bosch Sensixx B45L isn't producing steam?
If your Bosch iron isn't producing steam, ensure the boiler is switched on and the water tank isn't empty. Set the main power button to the “I” position and fill the water tank. Also, check that the steam regulation isn't set to the minimum position; increase the steam flow.
General| Power | 2400 W |
|---|---|
| Soleplate | Ceramic |
| Soleplate Material | Ceramic |
| Steam output | 40 g/min |
| Cord length | 2.5 m |
| Vertical Steam | Yes |
| Anti-Calc System | Yes |
| Drip-Stop System | Yes |
| Auto shut-off | Yes |
| Self-cleaning function | Yes |
| Anti-drip system | Yes |
| Type | Steam Iron |
How to adjust steam levels (low, medium, high) for optimal ironing.
Understanding the meaning of various indicator icons on the display.
Instructions for enabling or disabling audible feedback for touch controls.
To Next Page
