What to do if my Bosch Sensixx B45L isn't producing steam?
If your Bosch iron isn't producing steam, ensure the boiler is switched on and the water tank isn't empty. Set the main power button to the “I” position and fill the water tank. Also, check that the steam regulation isn't set to the minimum position; increase the steam flow.
Why does my Bosch Sensixx B45L Iron not heat up?
If your Bosch Iron does not heat up, ensure that the main power button is set to the “I” position, so that it is illuminated in red. Also, check that the temperature is set to the desired position.
How to fix Bosch Sensixx B45L not producing steam?
If your Bosch iron is not producing steam, it could be due to a couple of reasons. First, check if the boiler is switched on (the main power button should be set to the “I” position and illuminated in red) and ensure the water tank is not empty. If both are fine, then check if the steam regulation is set to the minimum position. If so, increase the steam flow.
Why is water flowing through the holes on the soleplate of my Bosch Sensixx B45L Iron?
If your Bosch Iron is leaking water through the soleplate, it could be due to several reasons. First, the steam function might be used before the iron has reached the correct temperature; try reducing the steam flow when ironing at low temperatures. Second, water might be condensing inside the pipes, especially if steam is being used for the first time or after a long period; point the iron away from the ironing area and press the steam release button until steam is produced. Finally, the steam generator may contain too much scale; clean the boiler as described in section “Calc’n’Clean Advanced” (F).
What to do if the “ ” icon flashes on my Bosch Sensixx B45L?
If the “ ” icon is flashing on your Bosch Iron, the steam release button on the iron handle hasn't been pressed in the last 8 minutes, activating the auto shut-off system. Press the steam release button again to switch the steam station back on.
Why is there water leakage from the boiler of my Bosch Iron?
If you notice water leakage from the boiler of your Bosch Iron, check if the filter located at the side of the appliance is loose and tighten it.
What to do if my Bosch Sensixx B45L does not stop steaming after placing it on the pad?
If your Bosch Iron doesn't stop steaming after placing it on the pad, it's likely because the “PulseSteam” function was activated by a double click. Just press the trigger once again, and the iron will stop steaming immediately.
Why is my Bosch Sensixx B45L not producing steam?
If your Bosch Iron isn't producing steam, ensure that the main power button is set to the “I” position (illuminated in red) and that the water tank is filled. Also, check that the steam regulation isn't set to the minimum; if it is, increase the steam flow.
Why is my Bosch Sensixx B45L Iron leaking water from the boiler?
If your Bosch iron is leaking water from the boiler, the filter located at the side of the appliance may be loose. Tighten up the filter to resolve this issue.
What to do if the Bosch Iron steam generator does not come on?
If the steam generator does not come on, first check the mains cable, the plug, and the socket to ensure there are no connection problems. Also, make sure that the main power button is set to the “I” position, so that it is illuminated in red.
General| Power | 2400 W |
|---|---|
| Soleplate | Ceramic |
| Soleplate Material | Ceramic |
| Steam output | 40 g/min |
| Cord length | 2.5 m |
| Vertical Steam | Yes |
| Anti-Calc System | Yes |
| Drip-Stop System | Yes |
| Auto shut-off | Yes |
| Self-cleaning function | Yes |
| Anti-drip system | Yes |
| Type | Steam Iron |
How to adjust steam levels (low, medium, high) for optimal ironing.
Understanding the meaning of various indicator icons on the display.
Instructions for enabling or disabling audible feedback for touch controls.
To Next Page
