What to do if my Bosch SM048 is short cycling?
If your Bosch Heat Pump is short cycling, several factors could be responsible. The unit might be oversized, requiring a recalculation of heating and cooling loads. The thermostat could be installed near a supply air grill, necessitating relocation, or the heat anticipator may need readjustment. Additionally, check for a defective or improperly calibrated low-pressure switch.
What to do if my Bosch SM048 has no flow or low flow?
If your Bosch Heat Pump experiences no flow or low flow, here's what you can check: * Verify the power supply. * Ensure the on/off switch is in the 'ON' position. * Engage the heat pump contactor. * Repair or tighten any broken or loose wires. * Purge air from the piping system. * Remove the pump cartridge and clean it if the pump shaft/impeller is stuck. * Replace the pump if it is defective. * Repair any kinks in the water piping and check for proper line size.
Why is the water temperature high in my Bosch Heat Pump?
High water temperature in your Bosch Heat Pump may be due to a stuck water temperature limit switch or a sensor that is not securely attached to the line.
General safety warnings for installation and servicing of the heat pump equipment.
List of components included in the standard package for the heat pump unit.
Defines warning symbols like NOTE, CAUTION, WARNING, and DANGER used in the manual.
Detailed explanation of the model number encoding for SM Series heat pumps.
Overview of SM Series heat pump configurations (VT, HZ, CF) and available factory options.
Instructions for moving and storing the heat pump unit safely and correctly.
Details on configuring the horizontal unit's blower orientation and required tools.
Step-by-step guide for reconfiguring the blower on left-hand horizontal units.
Detailed steps for removing the blower assembly from the unit.
Detailed steps for reinstalling the blower assembly after reorientation.
Steps for reinstalling the blower collar and associated brackets.
Steps for removing panels and disconnecting the motor on right-hand units.
Instructions for removing and reinstalling blower brackets on right-hand units.
Cautionary note regarding proximity of blower to air coil and potential damage.
Steps for sliding the blower assembly and reinstalling brackets.
Final steps for reinstalling panels and securing blower brackets.
Description of the counter-flow unit's dedicated downflow configuration.
Description of vertical unit field configuration for various orientations and options.
Important notes on discharge air configuration and blower/panel changes.
Diagrams illustrating top, back, and side discharge options for vertical units.
Table showing compatibility between blower orientation and electric heat.
Table detailing required steps for various vertical unit configurations.
Procedure for accessing internal components by removing panels.
List of tools required for vertical unit configuration tasks.
Steps for removing the condensing section access panels.
Procedure for removing the air handler panel and wiring caution.
Detailed instructions for reconfiguring the blower from UP to SIDE discharge.
Steps for removing the blower motor and inlet ring assembly.
Caution regarding proximity of blower to air coil and potential damage.
Steps for removing and reinstalling the blower collar and side panel cover.
Note that discharge air configuration change is not possible with Electric Heat Option.
Steps for reinstalling horizontal and vertical blower brackets in new orientations.
Caution regarding blower housing proximity to air coil and potential damage.
Final steps for reinstalling blower motor, inlet ring, and brackets.
Procedure for relocating condensate drain connection from front to back.
Steps for cutting, routing, and reattaching the condensate drain hose.
Instructions for relocating the HRP Pump Disconnect Switch wiring.
Procedure for relocating electric heat components for servicing.
Steps for removing electric heat elements and their covers.
Steps for reinstalling the electric heat E-box and elements.
Steps for removing the blower collar cover.
Description of the E-box design for field configuration and servicing.
Procedure for rerouting LCD wiring and reinstalling unit panels.
Information on the return and discharge duct flanges.
Notes on bending and installing the duct flanges.
Instructions for installing corner caps on the unit.
Guide to identifying corner cap identifiers and their locations.
Steps for installing corner caps and preparing the cabinet surface.
Guidelines for mounting vertical heat pump units.
Guidelines for mounting horizontal heat pump units.
Instructions for installing the hanging bracket kit on horizontal units.
List of components in the hanging bracket kit and field-provided items.
Steps for installing hanging brackets and hanging the unit.
Requirements for connecting and pitching the condensate drain line.
Note on condensate drain relocation for right-hand return conversion.
Guidelines for supply and return air duct connections and insulation.
Recommendations for supply and return piping sizing and material.
Notes on water flow rates, piping connections, and valve types.
Table detailing water quality parameters for scaling, corrosion, and fouling.
Warnings regarding compliance with electrical codes for field wiring.
Requirements for operating voltage and circuit protection.
Procedures for attaching conduit and routing power supply wiring.
Notes on separate power supplies required for units with internal electric heat.
Identification of UPM controller components and status indicators.
Notes on connecting thermostats to the unit's UPM board.
Wiring procedures for thermostat malfunction light connections.
Overview of the UPM controller and its safety controls.
Details on water and evaporator side freeze protection sensors.
Factory default settings for UPM board temperature, lockout, and alarm.
Explanation of UPM board timers like ANTI-SHORT CYCLE and BROWNout protection.
Configuration of alarm outputs for malfunction lights and display.
Caution regarding operation in test mode and component wear.
Details on freeze sensor settings, trip points, and alarm conditions.
Procedures for intelligent reset, hard lockout, and reset methods.
Location and function of the ECM interface board for motor control.
Explanation of thermostat connections and their functions on the ECM board.
Using CFM LED for airflow indication and measurement.
Description of thermostat outputs for compressor and fan control.
How to adjust airflow using the selector and DIP switches.
Selecting between Hot Gas Reheat and fan-only dehumidification.
Description of ECM motor features like efficiency and fan curve.
Instructions for changing the speed tap on ECM motors.
Explanation of HGRH functionality, operation, and availability.
Details on electric heat functionality, availability, and kW capacities.
Overview of the HRP option, its purpose, and major components.
Detailed operation of the HRP for heating potable water.
Caution regarding potential freezing damage to HRP units.
Functionality of the constant airflow motor for variable airflow settings.
Functionality and operation of the DPS water flow proving switch.
Application of the factory installed pump relay for energizing pumps or valves.
Description and function of the Comfort Alert Module for troubleshooting.
Explanation of Comfort Alert LED indicators and troubleshooting guidance.
Overview of the SSA device, its benefits, and technology.
Technical specifications for the Smart Start Assist device.
Explanation of the operational modes and their LED indicators.
Description of normal operation indicators for Smart Start Assist.
Description of undervoltage condition indicators for Smart Start Assist.
Description of overcurrent condition indicators for Smart Start Assist.
Description of incomplete ramp alarm indicators for Smart Start Assist.
Notes on LED status, recovery alarms, and time delays for SSA.
Steps for draining and flushing the water tank before HRP installation.
Instructions for installing the hot water (HR) piping for the HRP.
Steps for refilling the water tank and purging air.
Instructions for adjusting water heater thermostat settings for HRP.
Steps for initial start-up of the heat recovery system.
Detailed sequence of operation for cooling mode.
Detailed sequence of operation for heating mode.
Flowchart illustrating the logic for cooling and heating modes.
Considerations for well water systems, quality, and pressure.
Considerations for cooling tower and boiler loop systems.
Ensuring proper operation for closed loop and heating modes.
Notes on water piping exposure to freezing and insulation requirements.
Guidelines for piping connections, flushing, and valve installation.
Proper installation of ball valves for isolation and flow balancing.
Requirements for specialized design and installation of geothermal systems.
Use of GLP package and anti-freeze solutions for geothermal systems.
Checks to perform before energizing the unit after installation.
Verification of proper grounding and electrical wiring.
Verification of complete water piping and correct water flow.
Checks for proper blower rotation and vibration isolation.
Ensuring unit is serviceable and access panels are secured.
Considerations for thermostat and control wiring lead lengths.
Steps to start up the unit in cooling mode.
Recommended time for system equalization before operation.
Steps to start up the unit in heating mode.
Schedule for filter changes or cleaning based on environment.
Recommendation for an annual check-up by a qualified mechanic.
Information on blower motor lubrication requirements.
Procedure for checking and cleaning the condensate drain.
Common causes of periodic lockouts and troubleshooting steps.
Fields for customer information and unit identification.
Fields for recording unit nameplate data like model and refrigerant charge.
Fields for recording operating conditions in cooling and heating modes.
Fields for recording auxiliary heat data.
Contact details for technical support and information submission.
Table detailing UPM board LED colors, blinks, and error descriptions.
Common causes and checks for when the entire unit does not run.
Causes and checks for when the blower runs but the compressor does not.
Causes and checks for unit shutdown on high pressure control.
Causes and checks for unit shutdown on low pressure control.
Causes and checks for unit short cycling issues.
Causes and checks for insufficient cooling or heating performance.
Table of compressor start and run winding resistance values by model.
Troubleshooting information for Comfort Alert Module flash codes 3, 4, and 5.
Troubleshooting information for Comfort Alert Module flash codes 6, 7, 8, and 9.
Troubleshooting steps for HRP issues related to flow and water temperature.
Explanation of red LED status indications and corresponding actions.
Explanation of green LED status indications and corresponding actions.
Understanding flashing sequences and recovery modes for SSA.
Steps for mounting the thermostat subbase and preparing wires.
Information on connector locations and wiring notes for different motors.
Instructions for connecting W1/W2 and W2/EM terminals for 2-cool, 3-heat thermostats.
Table showing operating temperatures and pressures for cooling and heating.
Notes and assumptions regarding the performance data chart.
Operating temperatures and pressures for SM036 model at part load.
Operating temperatures and pressures for SM036 model at full load.
Operating temperatures and pressures for SM048 model at part load.
Operating temperatures and pressures for SM048 model at full load.
Operating temperatures and pressures for SM060 model at part load.
Operating temperatures and pressures for SM060 model at full load.
Operating temperatures and pressures for SM070 model at part load.
Operating temperatures and pressures for SM070 model at full load.
Table showing airflow data for ECM Constant Torque Motor X13.
Table showing airflow data for ECM Constant CFM Motor EON.
Table showing water pressure drop and additional pressure drop from hose kits.
Schematic diagram of the main unit's electrical wiring.
Important notes related to the main unit wiring diagram.
Wiring diagram for the UPM and Comfort Alert modules.
Important notes related to the UPM and Comfort Alert wiring diagram.
Wiring diagram for soft start option and ECM motor.
Important notes related to the soft start and ECM motor wiring diagram.
Wiring diagram for ECM motor control connections.
Important notes related to the ECM motor control wiring diagram.
Wiring diagram showing thermostat and ECM motor connections.
Important notes related to thermostat and ECM motor wiring.
Wiring diagram for the electric heater package.
Important notes related to the electric heater wiring diagram.
Diagrams for constant torque motor wiring harnesses.
Detailed harness diagram for constant torque motors.
Diagram showing wiring harness connections for constant airflow motors.
List of spare parts for the Vertical (VT) configuration.
Detailed table of VT configuration parts with part numbers.
Continuation of the spare parts list table for VT configuration.
Exploded view diagram of VT unit cabinet components.
Exploded view diagram of VT unit blower assembly components.
Exploded view of VT unit refrigeration and electrical components.
Detailed views of specific VT unit cabinet parts.
Detailed views of VT unit electrical and refrigeration components.
List of spare parts for the Horizontal (HZ) configuration.
Detailed table of HZ configuration parts with part numbers.
Continuation of the spare parts list table for HZ configuration.
Exploded view diagram of HZ unit cabinet components.
Exploded view diagram of HZ unit blower assembly components.
Exploded view of HZ unit refrigeration components.
Exploded view diagrams of HZ unit panel components.
Detailed views of HZ unit electrical components.
List of spare parts for the Counter Flow configuration.
Detailed table of Counter Flow configuration parts with part numbers.
Continuation of the spare parts list table for Counter Flow configuration.
Exploded view diagram of Counter Flow unit cabinet components.
Exploded view diagram of Counter Flow unit blower assembly components.
Exploded view diagrams of Counter Flow unit panel components.
Exploded view of Counter Flow unit refrigeration components.
Diagram and table showing dimensions for horizontal end blow units.
Table listing dimensions for horizontal end blow configurations.
Diagram and table showing dimensions for horizontal straight through units.
Table listing dimensions for horizontal straight through configurations.
Diagram and table showing hanging bracket locations for horizontal units.
Table listing hanging bracket location specifications.
Diagram and table showing dimensions for counter flow units.
Table listing dimensions for counter flow configurations.
Diagram and table showing dimensions for CF-Vertical units.
Table listing dimensions for CF-Vertical configurations.
To Next Page
General
