Bosch VPV 16 - VPV 45;63;80 to VPV 25;32, S.A.E. & Metric Combination, Installation Drawing

50 VPV Vane Pump
VPV 45/63/80 to VPV 25/32, S.A.E. & Metric Combination
{|
|
,yz
,y
IN
OUT
IN
OUT
,

y
{
,y
ø6.30
(ø160.0)
9.31
(236.5)
6.61
(168.0)
7.44
(189.0)
0.55
(14.0)
45° typ
METRIC 4-bolt
mounting flange
per ISO 3019/2
5.91
(150.0)
1.37
(34.91)
ø1.26
(ø32.0)
0.39 X 0.31
rectangular key
(10.0 X 8.0)
1.39
(35.23)
ø1.25
(ø31.74)
0.31
square key
(7.98)
9.31
(236.5)
5.91
(150.0)
Single stage control
Optional eye bolt
5.96
(151.4)
13.03
(330.8)
7.13
(181.0)
19.90
(505.4)
16.19
(411.1)
3.89
(98.9)
4.37
(111.0)
10.12
(257.2)
4.37
(111.0)
.76
(19.2)
1.53
(38.89)
Inlet port
std. SAE 2” pad
ø2.00
(ø50.8)
3.06
(77.78)
0.84
(21.44)
2.04
(51.7)
1.69
(42.88)
4.00
(101.5)
Case drain port
“METRIC” 3/8-19 BSPP
“SAE” #8 S.A.E.
SAE “C” 2-bolt
mounting flange
per ISO 3019/1
.69
(17.6)
5.96
(151.4)
13.03
(330.8)
DETAIL SAE-SAE DETAIL METRIC-METRIC
2.08
(52.8)
2.08
(52.8)
18.01
(457.5)
10.82
(274.9)
14.41
(366.1)
8.14
(206.8)
3.53
(89.7)
4.19
(106.4)
3.53
(89.7)
ø.47
thru support hole
(ø12.0)
17.43
(442.6)
Inlet port
“SAE” #24 S.A.E.
“METRIC” 1 1/2-11 BSPP
Compensator
adjusting knob
(CW rotation
increases
pressure
setting)
Case drain port
“SAE” #8 S.A.E.
“METRIC” 3/8-19 BSPP
Support point
“SAE” 3/8"-16UNC-2B TH’D
X
.87 deep
“METRIC” M10 X 1.5-6H TH’D (22.0)
“SAE” 1/2"-13UNC-2B TH’D
X
1.14 deep typ
“METRIC” M12 X 1.75-6H TH’D (29.0)
4 holes
SAE/METRIC SAE/METRIC
A
B
A
B
(SH.2 K-6)
(SH.2 D-6)
4.94
(125.4)
SINGLE STAGE CONTROL
NOT AVAILABLE ON VPV 45-164
Inches (millimeters)