EasyManuals Logo

Brocade Communications Systems NetIron CES 2000 Series User Manual

Brocade Communications Systems NetIron CES 2000 Series
118 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #91 background imageLoading...
Page #91 background image
and the status of the power supply. If you are not already attached to a terminal or a PC running
terminal emulation, see Displaying the status of the power supplies
device> show chassis
*** Brocade NetIron CES Series 2048CX ***
---POWERS ---
Power 1 ( 3I50 - AC 504W): Installed (OK)
Power 2: not present
Total power budget for system = 504 W
--- FANS ---
Metro fan tray (fan 1): Status = OK, Speed = LOW (50%)
Metro fan tray (fan 2): Status = OK, Speed = LOW (50%)
Metro fan tray (fan 3): Status = OK, Speed = LOW (50%)
Metro fan tray (fan 4): Status = OK, Speed = LOW (50%)
Metro fan tray (fan 5): Status = OK, Speed = LOW (50%)
Metro fan tray (fan 6): Status = OK, Speed = LOW (50%)
--- TEMPERATURE READINGS ---
CPU: Board 32.50C Chip 41.6C
481XG PPCR1: Board 32.50C Chip 43.31C
481XG PPCR2: Board 29.50C Chip 41.93C
2X10G PPCR: Board 33.0C Chip 41.68C
Fans are in auto mode. Temperature Monitoring Poll Period is 60 seconds
Base MAC Address = 001b.ed39.0300
Brocade NetIron CES Series 2048CX>
Syntax: show chassis
10-Gigabit Ethernet module installation or replacement
The 2-port 10-Gigabit Ethernet modules may optionally be installed or replaced in the field on the
Brocade NetIron CES Series 2024C, Brocade NetIron CES Series 2024F, Brocade NetIron CER Series
2024C, Brocade NetIron CER Series 2024F units. You can order the Brocade device with a 2 x10-
Gigabit module installed at the factory, or you can upgrade your device later.
This section provides the steps for installing, removing, and replacing the 10-Gigabit Ethernet module.
You will need the following tools to perform these procedures:
#2 Phillips-head screwdriver
Electrostatic Discharge (ESD) kit
DANGER
For safety reasons, the ESD wrist strap should contain a series 1 megaohm resistor.
Removing a 2 x10-Gigabit Ethernet module
Follow the procedure given below while removing a 2 x10-Gigabit Ethernet module.
1. Power off the Brocade device.
2. Use a #2 Phillips-head screwdriver to loosen the screws on the 2 x10-Gigabit module.
3. Remove the 2 x10-Gigabit module.
4. Place the 2 x10-Gigabit module in an anti-static bag for storage.
5. If you are removing the module without replacing it, install the blank faceplate in the front panel.
Installing a 2 x10-Gigabit Ethernet Module
Follow these procedures when installing a 10-Gigabit Ethernet Module.
10-Gigabit Ethernet module installation or replacement
Brocade NetIron CES 2000 Series and NetIron CER 2000 Series Hardware Installation Guide 91
53-1003823-01

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Brocade Communications Systems NetIron CES 2000 Series and is the answer not in the manual?

Brocade Communications Systems NetIron CES 2000 Series Specifications

General IconGeneral
BrandBrocade Communications Systems
ModelNetIron CES 2000 Series
CategorySwitch
LanguageEnglish

Related product manuals