SUMMER MODE
Your Caldera spa is equipped with a Summer Mode timer. The Summer Mode timer can be activated during extremely hot summer months if it
becomes difficult to maintain water temperatures low enough for comfort. Upon switching to the ON mode, the heater will immediately shut down
while the circulation pump (which can add heat to the water through normal operation) will remain on for approximately 5 minutes for heater cool-down. Both heater
and circulation pump will remain off for the next eight hours. Additionally, the summer mode icon on the main control panel will activate and remain active for as long
as the summer mode is on. Following this eight-hour period, the circulation pump, heater, and ozone will continue to turn off for an eight-hour period every day that the
switch remains in the ON position. In this way, the amount of heat transferred to the spa water will be minimized. When the outside temperatures begin to cool, the
Summer Mode timer should be turned to the OFF position (the summer mode icon on the main control panel shut off). This is the efficient 24 hour circulation mode
that keeps the heater operation and operating costs to a minimum during colder/heavier usage months.
NOTE: Whenever power is disconnected, and then reconnected to the spa, the Summer Mode timer will reset starting with the eight-hour shutdown mode. If a
different eight-hour shut down time is desired, deactivate the Summer Mode, then reactivate at the beginning of the desired eight-hour shut down time.
IMPORTANT: The Summer Mode will not lower the spa’s water temperature below the ambient air temperature.
To activate the Summer Mode, simply follow these steps:
1. Set the temperature control to 27°C (80°F).
2. On the control panel, simultaneously press and hold for 3 seconds “TEMP ▲ “ and “TEMP ▼ “.
The Summer Mode must be deactivated when cooler temperatures return. To do this, simply repeat step 2.
WARNING: Failure to deactivate the Summer Mode when the temperature drops below 0°C(32°F) will result in freezing of the spa. Damage resulting from this situation
is not covered under the terms of the warranty.
AUXILIARY CONTROL PANEL BUTTONS
(Available on
Geneva
TM
, Niagara
®
, Tahitian
®
, Elation
®
, and Aspire
®
spas)
The auxiliary control panel, conveniently located opposite the main control panel allows the user to activate the jets, air blower, and light.
JETS CONTROL
The “JETS 1” button activates jet pump 1. When the “JETS 1” button is pressed, the jets symbol will illuminate on the main control panel display. The symbol will
remain lit until the button is pressed again to turn off the jet pump 1, or after one hour of continuous operation when the pump is automatically shut off by the control
system.
The “JETS 2” button activates jet pump 2. When the “JETS 2” button is first pressed, the pump is in low speed and the jets symbol illuminates on the main control
panel display. Pressing the button a second time switches the jet pump to high speed mode. The symbol will remain lit until the button is pressed a third time turning
jet pump 2 off, or after one hour of continuous operation when the pump is automatically shut off by the control system.
AIR JETS BUTTON
(Available on
Geneva, Niagara, and Tahitian
spas)
The “AIR” button activates the air blower. When the “AIR” button is pressed, the air symbol will illuminate on the main control panel display. The symbol will remain lit
until the button is pressed to turn off the air blower, or after fifteen minutes when the blower is automatically shut off by the control system. While the air blower is on,
air only jets are operating throughout the spa. To stop the air blower when active, simply press the “AIR” button.
LIGHT CONTROL
(Available on
Geneva
TM
, Niagara
®
and Tahitian
®
spas)
L/T/S CONTROL (Available on
Elation
®
and Aspire
®
)
The “LIGHT” button activates the light and controls the intensity of the light. Pressing the “LIGHT” button operates the light as follows:
• 1st press of the “LIGHT” button – light will turn on to the maximum intensity.
• 2nd press of the “LIGHT” button – light will turn to medium intensity.
• 3rd press of the “LIGHT” button – light will turn to low intensity.
• 4th press of the “LIGHT” button – light will turn off.
If the light is left on, it will automatically be turned off by the control system after six hours of continuous operation. The light symbol on the main control panel will also
turn off when the light is deactivated.
If the light will not turn on, make sure SPA LOCK is deactivated. SPA LOCK disables the controls on both the main and auxiliary control panel.
MODE CONTROL
(Available on
Elation
and Aspire )
Pressing the “MODE” button initiates a 5 second operating window to perform the following functions:
• Press “JETS 1/▲” button – to increase volume.
• Press “JETS 2/▼” button – to decrease volume.
• Press “L/T/S” button – to advance to the next track (in CD mode)
• Press “L/T/S” button – to advance to the next available station (in radio mode).
NOTE: Five seconds after the last button is pressed, the auxilary panel defaults back to normal spa mode.
OPERATING INSTRUCTIONS
46
To Next Page
Loading...
