Candy CH64EXCP - Hob Cookware Advice; Use

6. USE
Swtch ON/OFF a heater zone
2) If there s resdual heat ndcaton n the dsplay whch s ON but n 0
power, "0" wll appear changng over.
To swtch OFF a heater Touch power key durng 1,2 sec. 3 Short
beeps wll be heard and nothng or "H" value wll appear n target zone
dgt f resdual heat exsts. Zone wll be OFF.
1) If any cookng stage s n poston 0, ths dsplay wll swtch OFF
automatcally after 10 seconds and the zone OFF sequence wll
sound.
3) If lock functon s actve you cannot swtch ON a zone.
To swtch ON a heater Touch power key durng 400 msec. Long beep
wll be heard and "0" value wll appear n target zone dgt, ndcatng
power level.
08 GB
8 8
8
8
8
8
Because of its low melting point, thin aluminium should not be used.
Glass-ceramic : not recommended. Poor performance. May scratch
the surface.
Cast Iron : usable, but not recommended. Poor performance. May
scratch the surface.
• Use pans whose diameter is wide enough to completely cover
the surface unit : the size of the pan should be no smaller than the
heating area. If it is slightly wider the energy will be used at its
maximum efficiency.
Aluminium : heavy weight recommended. Good conductivity.
Aluminium residues sometimes appear as scratches on the hob, but
can be removed if cleaned immediately.
distribution).
Stainless Steel : highly recommended. Especially good with a
sandwich clad base. The sandwich base combines the benefits of
stainless steel (appearance, durability and stability) with the
advantages of aluminium or copper (heat conduction, even heat
THE CHOICE OF COOKWARE - The following information will help
you to choose cookware which will give good performance.
Copper Bottom / stoneware: heavy weight recommended. Good
performance, but copper may leave residues which can appear as
scratches. The residues can be removed, as long as the hob is
cleaned immediately. However, do not let these pots boil
Porcelain/enamel : Good perfomance only with a thiny smooth, flat
base.
dry. Overheated metal can bond to glass hobs. An overheated copper
pot will leave a residue that will permanently stain the hob.
2.- Let touch control fnsh ts ntalzaton process.
Through the "Power management" function, the user can set the
maximum power that can be reached by the hob. Power management
function is only available during first 30 seconds after switch on the
hob. There is even the possibility to repeat this setting switching off
and on the power plug. By setting the desired maximum power, the
hob automatically adjusts the distribution in the various cooking zones
so that this limit is never exceeded; with the added advantage of being
able to simultaneously manage all the zones without overload
problems. The customer can set the maximum power of hob between
2.5 kW and the maximum related power of the hob (this can change
according to the model). For example if the maximum power of the hob
1.- Swtch on hob.
is 7 kW, the maximum power level for setting is between 2.5kW and
7 kW. After connecting the appliance to the electrical power, within 30
seconds you can set the power level based on the points shown
below:
3.-Unlock the control.
P
8
8
8
8
How to choose power management level
8 8
8
8
8
8
8 8
8
8
8
8
5.- After this moment, this message will appear on display, Po on timer
display. Power level divided by 100 in heater displays.
6.- Using '+' and '-' of Timer keys, Power Management value can be
adjusted. When requred value s selected, touch at the same tme “+”
and “–” keys durng 5 seconds.
7.- When ths process s fnshed, a long beep s heard and a reset s
produced. Start-up process wll be generated agan.
After that, touch control won´t allow any combnaton whch
can exceed ths lmt.
c) If ths power management selecton s ON, f any key s touched
except the combnaton of tmer “+” and “–”, process
Notes:
a) Ths power management s only avalable durng frst 30 seconds
after swtch on the hob.
b) If ths power management selecton s ON, f more than 90 seconds
after swtch on the hob ths process wll be fnsh wthout
any new power value were recorded.
wll be fnsh wthout any new power value were recorded and touch
control wll start workng as usual, wthout reset.
d) If ths power management selecton s ON, f any key s touched the
combnaton of tmer “+” and “–”, process wll be
fnsh wth a new power value were recorded , reset and touch
control wll start workng as usual.
4.- Before pass 30 seconds after switch on the hob; touch for 5
seconds “-” key of timer.
P
6
0
0
5
P
4
0
0
5
8.- After start-up process, n tmer dsplay power management wll be
showed.
P
4
0
0
5