Carrier 19XR - Page 34

34
0
Resettable
Fault
209 Fiber Offline 6
Fiber online to offline 6. The fiber-optic
communication link between the main
control board and M6 PLI transitioned
from online to offline.
Power down and then check the fiber-
optic communication connection
between the fiber interface circuit board
and M6 PLI for damage. Replace the
fiber-optic cable and/or fiber transceiver
circuit board if needed. See the
hardware service manual, publication
750-TG100 for PowerFlex 755T or
publication 750-TG101 for PowerFlex
755TS products, for the replacement
procedure. See the control pod fiber
diagram on the Tables & Graphics tab.
Coast (Motor Side Inverter). Stop
(Line Side Converter). Additional
Fault Action. Fault opens main circuit
breaker: Yes. Fault can automatically
reset: No. Emergency override
response: Cannot override this fault.
0
Resettable
Fault
210 Fiber Offline 7
Fiber online to offline 7. The fiber-optic
communication link between the main
control board and M7 PLI transitioned
from online to offline.
Power down and then check the fiber-
optic communication connection
between the fiber interface circuit board
and M7 PLI for damage. Replace the
fiber-optic cable and/or fiber transceiver
circuit board if needed. See the
hardware service manual, publication
750-TG100 for PowerFlex 755T or
publication 750-TG101 for PowerFlex
755TS products, for the replacement
procedure. See the control pod fiber
diagram on the Tables & Graphics tab.
Coast (Motor Side Inverter). Stop
(Line Side Converter). Additional
Fault Action. Fault opens main circuit
breaker: Yes. Fault can automatically
reset: No. Emergency override
response: Cannot override this fault.
0
Resettable
Fault
211 Fiber Offline 8
Fiber online to offline 8. The fiber-optic
communication link between the main
control board and M8 PLI transitioned
from online to offline.
Power down and then check the fiber-
optic communication connection
between the fiber interface circuit board
and M8 PLI for damage. Replace the
fiber-optic cable and/or fiber transceiver
circuit board if needed. See the
hardware service manual, publication
750-TG100 for PowerFlex 755T or
publication 750-TG101 for PowerFlex
755TS products, for the replacement
procedure. See the control pod fiber
diagram on the Tables & Graphics tab.
Coast (Motor Side Inverter). Stop
(Line Side Converter). Additional
Fault Action. Fault opens main circuit
breaker: Yes. Fault can automatically
reset: No. Emergency override
response: Cannot override this fault.
0
Resettable
Fault
212 Fiber Offline 9
Fiber online to offline 9. The fiber-optic
communication link between the main
control board and M9 PLI transitioned
from online to offline.
Power down and then check the fiber-
optic communication connection
between the fiber interface circuit board
and M9 PLI for damage. Replace the
fiber-optic cable and/or fiber transceiver
circuit board if needed. See the
hardware service manual, publication
750-TG100 for PowerFlex 755T or
publication 750-TG101 for PowerFlex
755TS products, for the replacement
procedure. See the control pod fiber
diagram on the Tables & Graphics tab.
Coast (Motor Side Inverter). Stop
(Line Side Converter). Additional
Fault Action. Fault opens main circuit
breaker: Yes. Fault can automatically
reset: No. Emergency override
response: Cannot override this fault.
0
Resettable
Fault
213 Fiber Offline 10
Fiber online to offline 10. The fiber-optic
communication link between the main
control board and L0 PLI transitioned
from online to offline.
Power down and then check the fiber-
optic communication connection
between the fiber interface circuit board
and L0 PLI for damage. Replace the
fiber-optic cable and/or fiber transceiver
circuit board if needed. See the
hardware service manual, publication
750-TG100 for PowerFlex 755T or
publication 750-TG101 for PowerFlex
755TS products, for the replacement
procedure. See the control pod fiber
diagram on the Tables & Graphics tab.
Coast (Motor Side Inverter). Stop
(Line Side Converter). Additional
Fault Action. Fault opens main circuit
breaker: Yes. Fault can automatically
reset: No. Emergency override
response: Cannot override this fault.
0
Resettable
Fault
214 Fiber Offline 11
Fiber online to offline 11. The fiber-optic
communication link between the main
control board and L1 PLI transitioned
from online to offline.
Power down and then check the fiber-
optic communication connection
between the fiber interface circuit board
and L1 PLI for damage. Replace the
fiber-optic cable and/or fiber transceiver
circuit board if needed. See the
hardware service manual, publication
750-TG100 for PowerFlex 755T or
publication 750-TG101 for PowerFlex
755TS products, for the replacement
procedure. See the control pod fiber
diagram on the Tables & Graphics tab.
Coast (Motor Side Inverter). Stop
(Line Side Converter). Additional
Fault Action. Fault opens main circuit
breaker: Yes. Fault can automatically
reset: No. Emergency override
response: Cannot override this fault.
Table 7 — Fault Codes by Port (cont)
PORT
CONDITION
DISPLAY
TEXT
FAULT ACTION FAULT ACTION
TYPE CODE