Carrier 42C Series - Page 15

15
Fig. 10 — 42CE Horizontal Furred-In With Plenum, Side Filter Access, and Electric Heat Unit Dimensions
L
K
Rear/Bottom Return
Rear Mtg. Holes
6-1//4
[160]
Max.
Unit Label and
Wiring Diagram
(See Note f)
Resilient Mounting
Grommet with 3/8 [10]
Dia. holes (Typ. of 4)
Strip Heater
High Limit
Electric strip
Heater Element
2
[51]
7/8 [22]
O.D.
Condensate
Drain
2-3/4
[71]
E
C
A
Drain Pan No Valve Pkg
1-1/4
[34]
2-1/4
[57]
Filter Removal
Both Sides
Optional
Service
Switch
See Note e
19.13
[486]
1-1/2
[38]
Top View
Front View
H
3/4
[19]
Typ
14-1/8
[360]
Chilled/Hot Water
Supply and Return
Connections
See Detail A
Optional Drip Lip
Mounting Location
No Valve Pkg
Shipped Loose
(See Note d)
1" [25] Supply
Duct Collar
3/4
[20]
24-3/16
[614]
23-1/4
Return
Air
10-1/2
[270]
G
F
Supply
Air
12
[303]
Right Side View
Detail A - Stub Out
Locations for
Standard Coils
B
Drain Pan with Valve Pkg
(Broken View)
*For other drain pan options see supplement.
21-9/16
[548]
Drip Lip with
Valve Pkg
Shipped Loose
(See Note d)
4-1/4
[108]
2-1/8
[53]
4-1/8
[106]
LEGEND
CR — Cold Water Return
HR — Hot Water Return
CS — Cold Water Supply
HS — Hot Water Supply
UNIT
SIZE
42CE
DIMENSIONS in. [mm]
a,b,c,d,e,f,g,h,i,j
NOTE(S):
a. Right-hand units shown, left-hand opposite.
b. All dimensions are ± .25 [6]. Drawing not to scale.
c. Product specifications are subject to change without notice.
d. Drip lip recommended. Provided when valve package is ordered.
e. Control box size and position may vary. Consult factory.
f. Position may vary.
g. Service entrance is located on the rear of the control box with knockouts.
h. Units without service switch use the knockouts on the rear side of the control box.
i. Typical size 06 unit shown with 1-Motor and 2-Blower. Refer to table for variation.
j. See valve package supplemental for piping termination.
QTY/UNIT
A B C E F G H K L Blower Motor
02 21-1/4 [540] 28-1/2 [724] 16 [406] 18-1/4 [464] 6-1/4 [159] 8-3/4 [222] 19-3/4 [502] 15-3/8 [391] 18-1/4 [464] 1 1
03 25-1/4 [641] 32-1/2 [826] 20 [508] 22-1/4 [565] 6-1/4 [159] 8-3/4 [222] 23-3/4 [603] 19-3/8 [493] 22-1/4 [565] 1 1
04 31-1/4 [794] 38-1/2 [978] 26 [660] 28-1/4 [718] 6-1/4 [159] 8-3/4 [222] 29-3/4 [756] 25-3/8 [654] 28-1/4 [718] 2 1
06 36-1/4 [921] 43-1/2 [1105] 31 [787] 33-1/4 [845] 7-1/2 [191] 10 [254] 34-3/4 [883] 30-3/8 [772] 33-1/4 [845] 2 1
08 43-1/4 [1099] 50-1/2 [1283] 38 [965] 40-1/4 [1022] 7-1/2 [191] 10 [254] 41-3/4 [1060] 37-3/8 [950] 40-1/4 [1022] 2 1
10 57-1/4 [1454] 64-1/2 [1638] 52 [1321] 54-1/4 [1378] 7-1/2 [191] 10 [254] 55-3/4 [1416] 51-3/8 [1306] 54-1/4 [1378] 4 2
12 65-1/4 [1657] 72-1/2 [1842] 60 [1524] 62-1/4 [1581] 7-1/2 [191] 10 [254] 63-3/4 [1619] 59-3/8 [1509] 62-1/4 [1581] 4 2