127
Table 104 — Low Ambient Control Board (SCB2) Inputs and Outputs
POINT
NAME
POINT
DESCRIPTION
I/O POINT
NAME
PLUG AND PIN
REFERENCE
SIGNAL PIN(S) PORT STATE
INPUTS
AN1 J5, 1-3 1=5v, 2=Vin, 3=GND (thermistor 1-2) (0 to 5VDC, thermistor, ohms)
AN2 J5, 4-6 4=5v, 5=Vin, 6=GND (thermistor 4-5) (0 to 5VDC, thermistor, ohms)
AN3 J5, 7-9 7=5v, 8=Vin, 9=GND (thermistor 7-8) (0 to 5VDC, thermistor, ohms)
AN4 J5, 10-12 10=5v, 11=Vin, 12=GND (thermistor 10-11) (0 to 5VDC, thermistor, ohms)
AN5 J5, 13-15 13=5v, 14=Vin, 15=GND (thermistor 13-14) (0 to 5VDC, thermistor, ohms)
AN6 J6, 1-3 1=5v, 2=Vin, 3=GND (thermistor 1-2) (0 to 5VDC, thermistor, ohms)
AN7 J6, 4-6 4=5v, 5=Vin, 6=GND (thermistor 4-5) (0 to 5VDC, thermistor, ohms)
AN8 J6, 7-9 7=5v, 8=Vin, 9=GND (thermistor 7-8) (0 to 5VDC, thermistor, ohms)
AN9 J7, 1-2 1 (thermistor, ohms)
AN10 J7, 3-4 3 (thermistor, ohms)
OUTPUTS
MM_A_VFD Motor Master VFD A AO1 J8, 1-2 1=0 to 20mA, 2=GND 0 to 20mA OUT
MM_B_VFD Motor Master VFD B AO2 J8, 3-4 3=0 to 20mA, 4=GND 0 to 20mA OUT
MM_A_RUN
Motor Master A
RunEnable
RLY1 J9, 1-3 1 = 2 = RLY1A, 3 = RLY1B 1 = Closes RLY1A/RLY1B
MM_B_RUN
Motor Master B
RunEnable
RLY2 J9, 4-6 4 =5 = RLY2A, 6 = RLY2B 1 = Closes RLY2A/RLY2B
RLY3 J9, 7-9 7 = 8 = RLY3A, 9 = RLY3B 1 = Closes RLY3A/RLY3B
RLY4 J9, 10-12 10 = 11 = RLY4A, 12 = RLY4B 1 = Closes RLY4A/RLY4B
RLY5 J9, 13-15 13 = 14 = RLY5A, 15 = RLY5B 1 = Closes RLY5A/RLY5B
Fig. 32 — Staged Gas Heat Control Board (SCB)
ADDRESS DIP
SWITCHES ALL ON
RED LED-
STATUS
GREEN LED-
LEN (LOCAL EQUIPMENT NETWORK)
J2
J1
PWR
J4
LEN
LEN
J3
4-POSITION
DIP SWITCH
PWR
1
13
10
7
XDCR/THERM
4
1
J6
J5
7
4
1
3
1
3
1
J8
0-20mA OUT
J7
THERMXDCR/THERM
1
4
13
10
7
RELAYS
J9
CEBD430427 HK50AA032 CEPL130427
To Next Page
Loading...
