Casio SI-460

24 25
MODE ANSWER
BACK DONE CHANGE
GRT MODESELECT
BACK ENTER NEXT
MODE ANNC ONLY
BACK DONE CHANGE
PLEASE SELECT
PHON ANSW OTHER
6.
7.Use the keypad to enter your ring selection
(2-9 or 0 for TS) choice.
8.
9.
Press
PROGRAM
to exit.
1.Press
PROGRAM
.
2.
3.
4.
5.
PROGRAMMING THE ANSWERING SYSTEM
SELECTING THE NUMBER OF RINGS
When the answering system is turned on, the ring select feature allows you to select the number
of rings, 2-9, or tollsaver (TS) before the unit will answer a call. By pressing “0” in the ring
select mode you can program tollsaver.
Tollsaver helps eliminate toll charges when calling in from a remote location by letting you know
if there are new messages before the unit answers. When set to TS (0), the unit answers calls
after the:
second ring = new messages
fourth ring = no new messages. Hang up after the third ring.
To program the ring select mode,
RING SELECT:TS
BACK SAVE
RING SELECT: 4
BACK CHANGE NEXT
GREETING SETUP
BACK ENTER NEXT
TIME&DAY SETUP
BACK ENTER NEXT
AUTO ATTND:OFF
BACK CHANGE NEXT
1.Follow steps 1-7 under “SETTING THE
GREETING TIMER ON” on
page 23.
2.
3.
Press to toggle between “ANSWER” and
“ANNC ONLY.”
PROGRAMMING THE ANSWERING SYSTEM
When greeting timer is on, you are able to
review the time that greeting 1 is scheduled to
play.
CHECKING
THE TIMES IN THE
GREETING / ANSWERING
SYSTEM TIMER
1.Follow steps 1-9 under “SETTING THE
GREETING TIMER ON” on page 23.
2.
The time that greeting 1 is programmed to
play will appear in the display.
3.Press
PROGRAM
to exit.
GRT TIMER ON
BACK CHANGE NEXT
09:30 TO 06:30
BACK CHNG ON/OFF
To turn the greeting timer off:
TURNING
GREETING / ANSWERING
SYSTEM TIMER OFF
1.Follow steps 1-9 under “SETTING THE
GREETING TIMER ON” on page 23.
2.
3.
4.
5.
Press
PROGRAM
to exit.
GRT TIMER ON
BACK CHANGE NEXT
09:30 TO 06:30
BACK SAVE ON/OFF
OFF
BACK SAVE ON/OFF
The SI-460 has two greeting modes for calls that are answered by a station’s answering system:
1. ANSWER:
All calls are answered, greetings play to the caller and the station allows the
callers to record messages.
2. ANNOUNCE ONLY:
All calls are answered, greetings play to the caller and a beep will be
heard to indicate the end of the greeting, but the caller cannot record a message at this
station. The caller can be instructed to dial another station’s extension where they can be
transferred to record a message. The SI-460 is factory preset to ANSWER mode.
SETTING THE GREETING MODE:
ANSWER OR ANNOUNCE ONLY
PROGRAMMING
PROGRAMMING
SETTING THE ANSWERING SYSTEM TIMER ON
1.Follow steps 1-20 under “SETTING THE
GREETING TIMER ON” on page 23 to set
the time you want your voice mail to turn
on and off.
2.
3.
Press
PROGRAM
to exit.
GRT2 FOR REST
BACK YES NO
To program the answer / announce only mode,
CONTINUED NEXT PAGE
SETTING THE GREETING MODE:
ANSWER OR ANNOUNCE ONLY
(cont.)
NOTE:
■ If a greeting has not been recorded, “PLEASE
RECORD GREETING No.1” will appear in the
display. See page 20 to record a greeting.
4.
5.
Press
PROGRAM
to exit.
The SI-460 can be set to turn your station’s answering system on at a pre-programmed time. The
remainder of the time, your answering system will be turned off.