Casio XJ-UT310WN Network Function Guide

9
Projecting Computer Screen Contents Over a LAN
Connection
This section covers everything you need to know for establishing a LAN connection between the
projector and a computer, and projecting the computer’s display contents.
There are a number of different ways to establish a LAN connection between the projector and a
computer. The workflow below describes what you need to do to create a LAN connection.
Workflow from LAN Connection to Projection
Install Network Connection on the computer*
1
“Software Required to Use Network Functions” (page 8)
Establish a wireless LAN connection between the
projector and computer
Establish a wired LAN connection between the
projector and a computer
“Connecting the Wireless Adapter to the Projector” (page 10)
“Connecting the
Projector to a
Computer via a
Wired LAN” (page
35)
z If you want to simplify the connection
process
z If you want to connect a computer
without connecting to an external
network (Internet or Intranet)*
2
z If you want to use an existing wireless
LAN access point (wireless router)
z If you want to connect a computer by
connecting to an external network
(Internet or Intranet)
“Establishing a Direct Wireless LAN
Connection between the Projector and a
Computer” (page 11)
“Establishing a Connection between the
Projector and Computer Via a Wireless LAN
Access Point” (page 29)*
3
“Using Network Connection” (page 39)
*1 After installing Network Connection on one computer, you can use the computer to create USB
tokens that can be used for LAN connection of other computers to the projector. For details, see
“Using the Token Wizard” (page 74).
*2 After establishing a direct wireless LAN connection between the projector and computer, the
computer will be able to connect with an outside network (Internet or Intranet) via the projector. For
more information, see “Connecting the Projector to an Outside Network without Terminating a
Direct Wireless LAN Connection with a Computer” (page 25).
*3 To connect this way, you need first to establish a direct LAN connection between the projector and
computer, and then configure settings to connect the projector to the wireless LAN access point.

Casio XJ-UT310WN Specifications

General

Matrix size	0.65 \
Matrix type	3-panel (p-Si TFT active)
Number of colors	16.78 million colors
Native aspect ratio	16:10
Projection distance	- m
Projection technology	DLP
Supported aspect ratios	16:9, 16:10
Contrast ratio (typical)	1800:1
Screen size compatibility	50 - 110 \
Projector native resolution	WXGA (1280x800)
Keystone correction, horizontal	-5 - 5 °
Focus	Manual
Offset	118 %
Throw ratio	0.28:1
Focal length range	- mm
Light source type	Laser/LED hybrid
Service life of light source	20000 h
Full HD	No
Supported video modes	1080i, 1080p, 480i, 480p, 576i, 576p, 720p
Analog signal format system	NTSC, PAL, PAL 60, PAL M, PAL N, SECAM
Microphone in	Yes
Audio (L/R) in	2
USB connector type	USB Type-A, USB Type-B
Serial interface type	RS-232
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
VGA (D-Sub) ports quantity	3
Wi-Fi standards	802.11b, 802.11g, Wi-Fi 4 (802.11n)
Noise level	34 dB
Noise level (economic mode)	29 dB
RMS rated power	16 W
Placement	Desktop, Ceiling
Product type	Ultra short throw projector
Product color	Grey, White
Power source	AC
AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	0.4 W
Power consumption (typical)	230 W
Operating altitude	0 - 3000 m
Operating temperature (T-T)	5 - 35 °C
Operating relative humidity (H-H)	20 - 80 %

Weight and Dimensions

Depth	332 mm
Width	414 mm
Height	152.4 mm
Weight	5500 g
Package depth	470 mm
Package width	594 mm
Package height	274 mm
Package weight	9620 g