CEM SPRINT - User Manual

Questions and Answers

G
gpooleAug 18, 2025
Why am I getting erratic results with my CEM SPRINT Analytical Instruments?
- H
  Heather ConleyAug 18, 2025
  If you're getting erratic results with your CEM Analytical Instruments, several factors could be the cause. Make sure that the sample size is consistent across all tests. Ensure the sample is correctly positioned in the sample cup. Check the iTAG stirring mechanism to confirm it's functioning properly. The optics might be dirty, so try cleaning them. Also, check and calibrate the balance to rule out any balance problems.
S
skiddAug 20, 2025
What to do if my CEM Analytical Instruments show a “No Flow Detected” error?
- A
  Amy CooperAug 20, 2025
  If you're seeing a “No Flow Detected” error on your CEM Analytical Instruments, first, ensure that water is available to the system. If water is available, check for any crimped tubing and replace it.
K
Karen WilliamsAug 23, 2025
How to fix wash station overflows in CEM SPRINT Analytical Instruments?
- M
  Mr. Erik JohnsonAug 23, 2025
  If the wash station is overflowing on your CEM Analytical Instruments, there are a few potential causes. The wash station itself might be clogged, so try cleaning it. Also, check the tubing for any clogs and clear them if necessary. Finally, inspect the waste tubing for any crimps and reposition or replace the tubing if needed. Cleaning the wash station is also a suggested solution.
J
jamespetersonAug 26, 2025
Why is the protein result too high or low on my CEM SPRINT Analytical Instruments?
- L
  Lisa BrewerAug 26, 2025
  If the protein result is too high or too low on your CEM Analytical Instruments, several factors could be the cause. First, verify the protein reference (Kjeldahl, etc.) and adjust it if necessary. Next, try to restandardize the iTAG. Additionally, dirty optics or a dirty homogenizer can affect results, so clean them accordingly.
D
douglas36Aug 28, 2025
What causes no iTAG added error in CEM Analytical Instruments?
- Z
  Zachary PerkinsAug 28, 2025
  If no iTAG is being added in your CEM Analytical Instruments, check for crimped tubing and replace it if necessary. Also, make sure that the cap on the iTAG bottle is not tightened; loosen it if it is.
D
Dylan BennettAug 30, 2025
How to stop water from splashing in the wash station of CEM SPRINT?
- K
  Kelly AlexanderAug 31, 2025
  If water is splashing in the wash station of your CEM Analytical Instruments, the pressure might not be properly set. Adjust the pressure to the correct range, which is typically between 10 and 15 psi.
V
Vincent GentrySep 2, 2025
Why is iTAG splattering in the sample cup of my CEM SPRINT Analytical Instruments?
- D
  deborah88Sep 2, 2025
  If the iTAG is splattering in the sample cup of your CEM Analytical Instruments, it could be due to a dirty homogenizer. Try cleaning the homogenizer. Alternatively, the homogenizer bearing might need replacement, so consider replacing it.
C
Carl NavarroSep 4, 2025
How to resolve unit-to-unit variability in CEM SPRINT Analytical Instruments results?
- C
  Carol PerezSep 4, 2025
  If you're experiencing unit-to-unit variability in results with your CEM Analytical Instruments, it could be due to an improper iTAG reference. Try re-running the Gold Standard.
J
Jasmine AndradeSep 7, 2025
What to do if the pressure is rising in CEM SPRINT Analytical Instruments?
- D
  dylankaufmanSep 7, 2025
  If you notice a rising pressure in your CEM Analytical Instruments, there may be debris in the regulator. Open, flush (clockwise), and then reset the regulator.
R
Robert JacksonSep 9, 2025
Why does the water in my CEM SPRINT system "steam"?
- L
  laliSep 9, 2025
  If the water in your CEM Analytical Instruments system "steams", it's likely due to improper heater calibration. You should calibrate the heater properly.