CipherLab 1662 L - Configure Related Settings

131 pages

Save Page as PDF

To Next Page

To Previous Page

106

Enter Setup

1662 L/1664 Barcode Scanner User Guide

3.1.3 CONFIGURE RELATED SETTINGS

Sniff Mode (Power-saving)

By default, this feature is enabled, meaning the scanner will listen to the wireless network at a

reduced rate.

*Enable

Disable

Main Page

Important Notices2
For USA3
For Canada3
For Hand-Held Product with RF Functions4
For Product with Laser4
Safety Precautions4
Care & Maintenance4
Release Notes5
Table of Contents7
Introduction11
Get Familiarized with 1662 L/1664 and 361012
Install the Battery into 1662 L/166412
Charge the Battery13
Charge the Battery Via Charger14
Use 361015
Inside the Package16
Product Highlights16
Symbologies Supported17
Quick Start19
Enter Configuration Mode21
Exit Configuration Mode21
Default Settings22
Save User Settings as Defaults22
Restore User Defaults22
Restore System Defaults22
Read a Setup Barcode23
Configure Parameters23
List the Current Settings27
Create One-Scan Setup Barcodes29
Understanding the Barcode Scanner33
Battery33
How to Operate the Scanner34
Auto Power off & Power-Saving35
Memory38
Transmit Buffer38
Memory Mode39
LED Indicator41
Good Read LED42
Good Read LED Duration42
Beeper43
Beeper Volume44
Good Read Beep45
Low Battery Alarm46
Vibrator46
Good Read Vibrator46
Good Read Vibrator Duration46
Send "NR" to Host48
Scan Modes49
Laser Mode50
Auto off Mode50
Auto Power off Mode50
Aiming Mode (1664 Only)51
Multi-Barcode Mode51
Continuous Mode (1662 L Only)52
Alternate Mode (1662 L Only)52
Scanning Timeout53
Delay between Re-Read54
Read Redundancy for All Symblogies55
Addon Security for UPC/EAN Barcodes56
Negative Barcodes56
Use Direct USB Cable57
Direct USB Interface57
Disable Direct USB Interface57
Picklist Mode (1664 Only)58
Pager Beep Duration58
Picklist Mode58
Time Stamp59
Date and Time Settings59
Separator for Date and Time61
Date Format62
Decode Setting (1664 Only)63
Aiming Pattern63
Decoding Illumination63
Decode Setting63
Hardware Reset64
Restore System Defaults64
Reset Connection64
Selecting Output Interface67
Bluetooth ® HID68
Bluetooth HID68
Activate Bluetooth ® HID & Select Keyboard Type69
Reset Connection70
Keyboard Settings71
Inter-Character Delay78
Inter-Function Delay78
HID Character Transmit Mode79
Keypad Support for Iphone/Ipad79
Bluetooth ® SPP Slave80
Bluetooth SPP Slave80
Activate Bluetooth SPP, Slave Mode80
Inter-Function Delay80
ACK/NAK Timeout81
Bluetooth ® SPP Master82
Bluetooth SPP Master82
Activate Bluetooth SPP, Master Mode82
Inter-Function Delay84
ACK/NAK Timeout85
Switch between Master/Slave Mode85
USB HID Via 361086
Activate USB HID & Select Keyboard Type87
Keyboard Settings88
Inter-Character Delay95
Inter-Function Delay95
HID Character Transmit Mode96
USB Virtual COM Via 361097
Activate USB Virtual COM97
Inter-Function Delay97
ACK/NAK Timeout98
Direct USB HID99
Activate USB HID & Select Keyboard Type100
Keyboard Settings101
Inter-Character Delay108
Inter-Function Delay108
HID Character Transmit Mode109
Direct USB Virtual COM110
Activate USB Virtual COM110
Inter-Function Delay110
ACK/NAK Timeout111
Set up a Wpan Connection113
Connecting Via 3610114
Connect to 3610114
Change Interface115
Configure Related Settings116
Dongle117
Change Interface117
Configure Related Settings118
Connect to Dongle121
Specifications129

CipherLab 1662 L - Configure Related Settings

Table of Contents

Related product manuals