Cisco ASR 1002 Quick Start Guide

24
for management of the system, extended setup will ask you
to configure each interface on the system
Would you like to enter basic management setup? [yes/no]: n
First, would you like to see the current interface summary? [yes]: y
Any interface listed with OK? value "NO" does not have a valid configuration
Interface IP-Address OK? Method Status Protocol
GigabitEthernet0/0/0 unassigned NO unset down down
GigabitEthernet0/0/1 unassigned NO unset down down
GigabitEthernet0/0/2 unassigned NO unset down down
GigabitEthernet0/0/3 unassigned NO unset down down
GigabitEthernet0 unassigned YES unset administratively down down
Configuring global parameters:
Enter host name [Router]:
The enable secret is a password used to protect access to
privileged EXEC and configuration modes. This password, after
entered, becomes encrypted in the configuration.
Enter enable secret: test
The enable password is used when you do not specify an
enable secret password, with some older software versions, and
some boot images.
Enter enable password: tests
The virtual terminal password is used to protect
access to the router over a network interface.
Enter virtual terminal password: test
Configure SNMP Network Management? [yes]: n
Configure IP? [yes]: y
Configure RIP routing? [no]:
Configure bridging? [no]:
Configure CLNS? [no]:
Configuring interface parameters:
Do you want to configure GigabitEthernet0/0/0 interface? [yes]: n
Do you want to configure GigabitEthernet0/0/1 interface? [yes]: n
Do you want to configure GigabitEthernet0/0/2 interface? [yes]: n
Do you want to configure GigabitEthernet0/0/3 interface? [yes]: n
Do you want to configure GigabitEthernet0 interface? [no]: n
The following configuration command script was created:
hostname Router
enable secret 5 $1$6r./$U5wHcV3uRWkKWK/fap474.
enable password tests
line vty 0 4
password test
no snmp-server
!
ip routing
no bridge 1
no clns routing
!
interface GigabitEthernet0/0/0
shutdown

Cisco ASR 1002 Specifications

General

Ethernet LAN	Yes
Cabling technology	10/100/1000Base-T(X)
Networking standards	IEEE 802.3
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet interface type	Gigabit Ethernet
DHCP client	-
Supported network protocols	BGP, GRE, OSPF, DVMRP, EIGRP, IS-IS, IGMPv3, PIM-SM, PIM-SSM
Ethernet LAN (RJ-45) ports	4
Security algorithms	SSH
VPN tunnels quantity	8000
Safety	UL60950-1 CSA, C22.2 No. 60950-1-03, EN 60950-1, IEC 60950-1, AS/NZS 60950.1
Certification	FCC 47CFR15 Class A AS/NZS CISPR 22 CISPR 22 Class A EN55022 Class A ICES-003 Class A VCCI Class A CNS-13438 Class A EN61000-3-2 EN61000-3-3
Internal memory	4096 MB
AC input voltage	85 - 264 V
Power source type	AC
AC input frequency	50 - 60 Hz
Power consumption (typical)	560 W
Operating altitude	0 - 3048 m
Storage temperature (T-T)	0 - 50 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	5 - 95 %
Operating relative humidity (H-H)	5 - 90 %
Product color	Gray
Rack capacity	2U

Weight and Dimensions

Depth	461 mm
Width	437.4 mm
Height	89 mm
Weight	- g