Cisco ASR1002 - Chassis Ground Connection Installation

10
This completes the procedure for installing the cable-management brackets on a Cisco ASR 1002 Router for a chassis
rack-mount configuration.
Chassis Ground Connection Installation
Connecting the Cisco ASR 1002 chassis to earth ground is required for all DC-powered installations and AC-powered
installations where compliance with Telcordia grounding requirements is necessary.
Caution The dual-lug chassis ground stud must be installed, and all the cards and filler plates must be fully inserted and
screwed in and earthed to prevent a potential hazard in a telecom line.
Have the recommended tools and supplies available before you begin this procedure.
Warning This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the absence of
a suitably installed ground conductor. Contact the appropriate electrical inspection authority or an electrician if
you are uncertain that suitable grounding is available. Statement 1024
Before you connect the power or turn on the power to your router, you must provide an adequate chassis ground (earth)
connection for the Cisco ASR 1002 Router. The chassis ground lugs (two) and the respective screws (four) are provided in the
accessory kit that is shipped with your Cisco ASR 1002 Router.
The following tools, equipment, and supplies are necessary to connect the system ground to the chassis:
• Phillips screwdriver
• Dual-lug chassis ground component (two) and respective screws (four)
• Grounding wire
See Figure 6 for the location of the chassis ground connector on the Cisco ASR 1002 Router.
Figure 6 Cisco ASR 1002 Router Ground Connector Location and eUSB Panel Door
Perform the following steps to install chassis ground connection:
Step 1 Use the wire stripper to strip one end of the AWG #6 wire approximately 0.75 inches (19.05 mm).
1
F0 with Cisco ASR1000-ESP5 or Cisco ASR1000-ESP10
Note The Cisco ASR10002 Router does not support
the Cisco ASR1000-ESP20 module.
3
The eUSB panel door on the side of the Cisco ASR 1002
Router must not be opened. If there is a problem with the
eUSB flash card, the chassis should be returned.
2
R0 slot with embedded ASR1000-RP1 (Cisco
ASR1000-RP2 is not supported by the Cisco ASR1002
Router) and embedded ASR1000-SIP10
4
Cisco ASR 1002 Router ground stud location
AS
R
1
002
s
t
a
t
p
w
r
m
in
m
aj
c
r
it
S
P
A
-
4XOC
3-P
OS
S
T
A
T
U
S
0
1
2
3
C
/A
A
/
L
C
/A
A
/L
C
/A
A
/
L
C
/A
A
/L
S
P
A
-
4XOC
3-P
OS
S
TA
TU
S
0
1
2
3
C
/A
A
/
L
C
/A
A
/L
C
/
A
A
/
L
C
/A
A
/
L
S
TA
T
Q
E
0
Q
E
1
QE
2
QE
3
B
O
O
T
C
A
R
R
IE
R
L
I
N
K
P
W
R
S
T
ATM
T
S
MG
M
T
A
U
X
C
O
N
S
P
A-4XOC3
-P
OS
S
T
A
T
U
S
0
1
2
3
C
/
A
A
/L
C
/A
A
/L
C
/A
A
/
L
C
/
A
A
/L
3
1
2
4
280283