Cisco UCS C240 M3 Specifications

Cisco UCS C240 M3 High-Density Rack Server (Small Form Factor Disk Drive Model)
CONFIGURING the SERVER
35
— Fusion ioDrive2 cards can be installed in slots 1, 2, or 3. Note that the only the Cisco
UCS 3.0 TB MLC Fusion ioDrive2 card is full-height; all other Fusion ioDrive2 cards
are half-height and therefore may need an adapter to hold them securely in the
available slots.
■ For 2-CPU systems:
— Five PCIe slots are available, three on PCIe riser 1 (PCIe slots 1, 2, and 3) and two on
PCIe riser 2 (PCIe slots 4 and 5).
— All of the slots are full-height except slot 4.
— Two VIC cards may be installed in 2-CPU systems, using slots 2 or 5. See Table 1 on
page 8 for the slot descriptions.
— Up to four Cisco UCS 3.0 TB MLC Fusion ioDrive2 full-height cards are supported and
can be installed in slots 1, 2, 3, or 5.
— Up to five of the other Fusion ioDrive2 cards (1205-, 785- and 365-GB versions) are
supported and can be installed in slots 1, 2, 3, 4, and 5, although an adapter may be
needed when installing one of these half-height cards in slots 1, 2, 3, or 5 (the
full-height slots).
■ Additional considerations for the Cisco VIC 1225:
— Supports 10G SFP+ optical and copper twinax connections.
— The server supports installation of up to two Cisco VIC 1225 cards and they are
supported only in PCIe slots 2 and 5.
— The primary slot for the Cisco VIC 1225 is PCIe slot 2. If there is only one card, it
must be installed in PCIe slot 2.
— To use the Cisco Card NIC mode, this card must be installed in PCIe slot 2. Slot 2 can
operate while the server is in standby power mode.
— Requires that the server has CIMC firmware version 1.4(6) or later installed. There is
a heartbeat LED on the top of the card that indicates when firmware is active.
— To use this card for UCS integration (Cisco UCS Manager mode) with Cisco UCS
Manager 2.1(0) or later, the minimum card-firmware and uboot image level is
2.1(0.306).
■ To help ensure that your operating system is compatible with the card you have selected, or
to see additional cards that have been qualified to work with the UCS C240 M3 server, but
are not sold on the Cisco pricelist, check the Hardware Compatibility List at this URL:
http://www.cisco.com/en/US/products/ps10477/prod_technical_reference_list.html
STEP 7 ORDER OPTIONAL NETWORK CARD ACCESSORIES
Copper twinax cables and SFP optical modules may be ordered to support the two-port network cards that
are available with the server.

Cisco UCS C240 M3 Specifications

General

Processor cores	8
Processor model	E5-2600
Processor frequency	2.7 GHz
Number of processors installed	2
HDD size	2.5 \
RAID support	Yes
HDD interface	-
Optical drive type	No
Total storage capacity	300 GB
Maximum storage capacity	- TB
Number of HDDs installed	16
Memory slots	24
Internal memory	96 GB
Memory clock speed	1866 MHz
Internal memory type	DDR3-SDRAM
Maximum internal memory	- GB
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
PCI Express x8 slots	3
Chassis type	Rack (2U)
Power supply	650 W
Operating altitude	0 - 3000 m
Non-operating altitude	0 - 12000 m
Operating temperature (T-T)	-40 - 70 °C
Storage relative humidity (H-H)	5 - 93 %
Operating relative humidity (H-H)	10 - 90 %
Harmonized System (HS) code	84714100

Weight and Dimensions

Depth	712 mm
Width	445 mm
Height	87 mm