Note:
Be sure
to
read this chapter referring to the front diagrams
of
chapter
"3.
CONTROLS" on
page
5 (unfold).
Basic Operations
When
the
unit
is
turned
on,
starting
and
stopping
the
engine
with
its
volume
raised
to
the
maximum
level
may
harm
your
hearings. Be
careful
about
adjusting
the
volume.
Note:
• Use this unit
after
starting the engine.
~
EngineON
\..?WJ
position
Adjusting
the volume
1.
Operate the [VOL] button in the direction
of
the + (up)
or
- (down) to adjust the volume;
+ : Increases the volume.
- : Decreases the volume.
*The volume level indicated
in
the display
is
in
a
range from
0 (minimum) to 33 (maximum).
ACAUTION
MAIN Display
While
driving,
keep
the
volume
at a level at
which
external
sounds
can be heard.
.
....
-
..
, .
-
no
4
~
:
....
: :
:.
, '-"0
,-",
,.n
o
","
)
...
1.1t
...
I
r.Yf
...
!;
I.! ;
""1
.J
..
'-
....
'
........
'
23
VRX755VD
~
ClockTime Display
l
SUB Display
l
MAIN Display
; ;r C
'r
.:;~n
.:~._b,:I.:C.:;
P.C~
..J=i
)
:/lEr.:
...
J
i_or
_ _
SWitching the
display
When the
panel
is
closed:
1.
Press the [DISP] button to select the desired
display.
Each time you press the
[DISP] button, the
display switches
in
the following order:
Notes:
• Once selected, the preferreddisplay becomes the
default display. When
a function adjustment such
as volume is made, the display momentarily
switches to that function's display, then returns
back to the preferred display several seconds
after the adjustment.
•
If
a title has been input, it is shown in the SUB
display.
If
no title has been input, "NO TITLE"
appears in the display.
To
input a title, refer
to
the
subsection
"Entering
titles"
in
"Other
Functions"
section.
• For CD
and
TV,
some special characters
of
the
title will
not
be displayed on the Information Panel
of
the
DCP.
In this case, those characters will only
be left blank.
•
SUB
displays do not appear when panel is open.
•
SUB
displays do not appear when
2-Z0NE
function is ON.
Turning
on
and
off
the
power
Note:
• Be careful about using this unit for a long time
without running the engine.
Ifyou drain the car's
battery too
far,
you may not be able
to
start the
engine
and
this can reduce the service life
of
the
battery.
1.
Press the [SOURCE] button.
2. The illumination and display on the unit light
up. The unit automatically remembers its last
operation mode and will automatically switch
to display that mode.
3.
Press and hold the [SOURCE] button for 1
second
or
longer to turn off the power for the
unit.
Note:
•
About
the "SYSTEM CHECK"
The
confirmation
of
connected equipment must be
performed for this unit only when the wiring
connection is complete and power
is turned
on
to
the unit
first.
When
the poweris supplied, "PUSH
PWR"appear in the
display.
Press the [SOURCE]
button, the
system check starts inside the unit.
When
"COMPLETE"
and
"PUSH PWR" appear
alternately, press once again the [SOURCE] button.
Selecting a mode
1. Press the [SOURCE] button to change the
mode of operation.
2. Each time you press the [SOURCE] button,
the mode of operation changes in the
following order:
Radio mode
-.
(SIRIUS mode)
-.
DVD
mode
-.
(CD changer mode)
-.
(DVD
changer mode)
-.
(TV mode)
-.
VISUAL
mode
-.
(iPod mode)
-.
Radio mode...
*External equipment not connected with
CeNET
is
not selected.
* When 2-Z0NE function
is
ON,
the main unit's
[SOURCE] button operates for the MAIN zone
only; use the accessory remote control unit to
switch to a SUB zone source.
To Next Page
Loading...
Need help?
General
