Basic
Operations
Housing
the
liquid
crystal
panel
1. Press the [OPEN] button and
the
liquid
crystal panel is housed automatically.
Note:
• When leaving this unit unused for a long period
of
time
or
leaving your
car,
be sure to house the
liquid crystal panel into the main
unit
Turning the
liquid
crystal
panel
horizontal
(Air
conditioner
operation mode)
When the
way
the liquid crystal panel is
mounted hinders
the
operation
of
the
air
conditioner,
the
position
of
the panel can be
turned horizontal temporarily.
1. Press and hold the [OPEN] button when the
liquid crystal panel is upright,
and
release the
button when a beep is heard.
2.
The
liquid crystal panel turns horizontal.
';'
Press the [OPEN] button again when the
liquid crystal panel is
in
the horizontal position,
and the panel returns to the original position.
*The unit can also be set so that the panel
returns to its original angle after a set time
in
the horizontal position (See
P.28).
Mute
1. When in the radio, SIRIUS, VISUAL
or
TV
mode, each time you press the [MUTE]
button, mute is turned on and off. "MUTE"
appears
when
mute is turned on.
2. In
modes
other
than radio, SIRIUS, VISUAL,
or
TV, enable the
MUTE
function by holding
the [MUTE] button depressed
for
1 second
or
longer.
Regarding the menu screens [RTN]
and
[ESC] keys
• [RTN]: Touch
the
[RTN] key to return
to
the
previous screen.
• [ESC]: Touch the [ESC] key
to
return
to
the
main screen.
In the
ADJUST
mode, pressing the
[ADJ]
button
will also cause a return to the main screen.
In cases where this kind
of
multiple
key
response is supported, the following kind of
notation will be used:
Touch the [RTN]
key,
[ESC]
key,
or
press the
[ADJ] button.
Adjusting
the AUDIO
Note:
• When the
separately~sold
5.
1 ch Surround
Decoder (DVH940) is used, the bass
and
treble
tone adjustments cannot be made.
To
adjust the
tone, refer to the section
"5.
1
ch
Surround
Decorder
Operations".
Adjusting
the balance/fader
1.
Press the
[ADJ]
button, then touch
the
[AUDIO]
key.
2.
Touch the
[SAL/FAD]
key.
3. Touch the
[.]
or
[T]
key
to
adjust
to
the
fader level.
*The factory default setting is "0". (Adjustment
range: front 13 to rear
13)
[.]
key: Emphasized the sound from the
front speakers.
[T]
key:
Emphasized the sound from the
rear speakers.
4. Touch the [....] or
["'1
key
to
adjust
to
the
balance level.
*The factory default setting is
"0".
(Adjustment
range: left
12
to right 12)
[....]
key:
Emphasized the sound from the left
speakers.
[
...
]
key:
Emphasized the sound from the
right speakers.
5. Touch
the
[RTN]
key,
[ESC]
key,
or press the
[ADJ]
button.
Adjusting
the BASS
The bass gain, bass frequency (center frequency)
and bass Q can be adjusted as follows.
1.
Press the [ADJ] button, then touch the
[AUDIO]
key.
2. Touch the
[BASS]
key.
3.
When
the bass type selection screen is
displayed, touch the key for the desirable
type
to
select it.
4. Touch the
[.]
or
[T]
key to adjust to
desirable level.
GAIN :
-6
to 8 (The factory default setting
is "0")
FREQ. : 50Hz/80Hz/120Hz (The factory
default setting is "50")
Q : 1/1.25/1.5/2 (The factory default
setting is "1")
5.
Touch the [RTN]
key,
[ESC]
key,
or
press the
[ADJ]
button.
VRX755VD
25
To Next Page
Loading...
Need help?
General
