Clarion VRX8370R User Manual

Operating the DSP and Equalizer
Note:
e
if
the
control
is
idle
for
about
5
seconds
after
each
operation,
the
unit
returns
to
the
previous
mode.
1)
Press
the
EQ
button
[14]
to
go
to
the
equaliz-
er
mode.
Press
the
ADJ
button
[15]
to
display
the
setting
menu.
3)
Slide
the
a-selector
[1]
to
A
(up)
and
W
(down)
to
select
the
item
and
slide
the
a-
selector
[1]
to
(right)
to
change
the
setting.
The
following
items
can
be
set.
¢
SUB
WOOFER:
STEREO/MONO/OFF
Switches
the
settings
according
to
the
no.
of
speakers.
¢EQ
MINFREQ:
30/50
Sets
the
lowest
frequency.
+P.
EQ:
FRONT/REAR/OFF
Switches
the
front
and
rear.
¢
SURROUND:
ON/OFF
Turns
on
and
off
the
surround
effect.
When
setting
the
item
SUB
WOOFER
or
P.
EQ
in
“PUSH
ENT’,
if
you
press
ENT
of
the
a-selector
[1],
the
adjustment
mode
is
set.
For
information
about
the
adjustment
mode
of
each
item,
see
the
next
subsection
“Setting
in
the
adjustment
mode’.
After
completing
the
setting,
press
the
EQ
button
[14]
to
return
to
the
previous
mode.
2
—
=
Setting in the adjustment mode
Note:
e When the sub woofer or parametric equalizer is
turned off, it cannot be adjusted.
Select an item to be adjusted following step 3) in
the previous subsection “Basic settings” and
press ENT of the a-selector [4]. The setting
mode is displayed and each adjustment window
is displayed.
Slide or press the a-selector [1] following the
instruction on the display and make setting.
Adjusting the sub woofer
Volume or filter of the sub woofer is set.
Items shown in the table below can be set.
38 VRX8370R
Description
Slide the a-selector [1] to A (up) or V
tas
(down)
to
adjust
the
volume
of
the
(down) to set the frequency of the low
pass filter.
PF
LOP*?
|
(42
dB/oct
©
18
dB/oct
©
24
dB/oct)
Slide the a-selector [1] to & (up) or V
pF
(down)
to
set
the
frequency
of
the
high
pass filter.
HPF
T
Slide the a-selector [7] to & (up) or ¥
L
Slide
the
o-selector
[1]
to
&
(up)
or
V
S
(down)
to
set
the
slope
of
low
pass
filter.
H
OL woofer. (0 to 4)
LPF
(50 Hz <> 80 Hz © 120 Hz)
(Through «> 50 Hz © 80 Hz © 120 Hz)
Slide the o-selector [1] to & (up) or V
(down) to check the wiring of the speakers.
Slide the a-selector [1] to & (up) or V
(down)
to
set
the
slope
of
high
pass
filter.
SLOP*2
|
(12
dB/oct
©
18
dB/oct
©
24
dB/oct)
(OFF <> FRONT-L © FRONT-R ©
REAR-L © REAR-R @ WOOFER-L @
TEST
ONE*S
WOOFER-R © ALL ch)
*1: To move the cursor to the next item, slide the a-
selector
[1]
to
>
vot
and
to
the
previous
item,
slide the button to q (left). (If you slide and hold
the a-selector [4] to <q (left), the adjustment
menu returns.)
*2: The LPF SLOPE and the HPF SLOPE can be
adjusted when the DPH9300 is connected.
*3: The TEST TONE can be adjusted when the
DPH9300/DPH7300 is connected.
Note:
e The seiting for the sub woofers cannot be preset
in “USERT to 6”.
Adjusting the parametric equalizer
Frequency characteristic in the cabin space can
be adjusted.
The items shown in the table below can be
adjusted.
Press ENT of the a-selector [1] to output the
TEST TONE (PINK NOISE) in the following order.
(eels —*»REAR—> ALL-—~> rea)
¢ The preset selection display appears first.
Note:
e The settings made for the parametric equalizer
cannot be preset in “USERT to 6”.

Clarion VRX8370R Specifications

General

Brand	Clarion
Model	VRX8370R
Category	Car Receiver
Language	English