To Next PageTo Next PageHow to troubleshoot main power problems in ClimateMaster Heat Pump?
If your ClimateMaster Heat Pump has main power problems and the Green Status LED is off, check the line voltage circuit breaker and disconnect. Also, check for line voltage between L1 and L2 on the contactor, for 24VAC between R and C on CXM/DXM, and the primary/secondary voltage on the transformer.
Why does my ClimateMaster Heat Pump unit short cycle?
If your ClimateMaster Heat Pump unit short cycles, it could be due to several reasons. A dirty air filter can cause short cycling, so check and clean it. Also, the unit might be in 'test mode'; reset the power or wait 20 minutes for it to automatically exit this mode. The unit might be oversized for the space; check the sizing for the actual load of the space. Finally, the compressor might be overloaded, so check it and replace it if necessary.
Why does only the fan run on my ClimateMaster Tranquility TTH072 Heat Pump?
If your ClimateMaster Heat Pump only runs the fan, it could be due to the following reasons: * Thermostat position: Ensure the thermostat is set for heating or cooling operation. * Unit lockout: Check for lockout codes and reset the power. * Compressor Overload: Check the compressor overload and replace it if necessary. * Thermostat wiring: Check the thermostat wiring at the heat pump. Jumper Y and R for compressor operation in test mode.
What does LP/LOC Fault Code 3 mean on my ClimateMaster Tranquility TTH072?
If your ClimateMaster Heat Pump is showing the LP/LOC Fault Code 3, indicating low pressure or loss of charge, it could be due to insufficient charge. Check for refrigerant leaks. Alternatively, the compressor might be pumping down at start-up, so check the charge and start-up water flow.
Why does only the compressor run on my ClimateMaster Heat Pump?
If your ClimateMaster Heat Pump only runs the compressor, it could be due to the following issues: * Thermostat wiring: Check the G wiring at the heat pump. Jumper G and R for fan operation. * Fan motor relay: Jumper G and R for fan operation. Check for Line voltage across BR contacts. * Fan motor: Check for line voltage at the motor and check the capacitor. * Reversing valve: Set for cooling demand and check 24VAC on RV coil and at CXM/DXM board. If the RV is stuck, run high pressure up by reducing water flow and while operating engage and disengage RV coil voltage to push valve. * Thermostat setup: Check for ‘O’ RV setup not ‘B’. * Thermostat wiring: Check O wiring at heat pump. Jumper O and R for RV coil ‘click’.
What does LT1 Fault Code 4 mean on my ClimateMaster Tranquility TTH072 Heat Pump?
If your ClimateMaster Heat Pump displays the LT1 Fault Code 4, which indicates a water coil low temperature limit, it could be due to: * Reduced or no water flow in heating: Check the pump operation or water valve operation/setting. Also, check water flow and adjust to proper flow rate. Clean or replace any plugged strainer or filter. * Inadequate antifreeze level: Check the antifreeze density with a hydrometer. * Improper temperature limit setting: Clip JW3 jumper for antifreeze (10°F [-12°C]) use. * Water temperature out of range: Bring the water temperature within design parameters. * Bad thermistor: Check the temperature and impedance correlation per chart.
What does LT2 Fault Code 5 mean on my ClimateMaster Tranquility TTH072?
If your ClimateMaster Heat Pump displays the LT2 Fault Code 5, indicating an air coil low temperature limit, it may be caused by: * Reduced or no air flow in cooling: Check for a dirty air filter and clean or replace it. Also, check the fan motor operation and any air flow restrictions. Ensure that the external static isn't too high. * Air temperature out of range: Ensure that the entering air temperature is within design parameters. * Improper temperature limit setting: Normal airside applications will require 30°F [-1°C] only. * Bad thermistor: Check the temperature and impedance correlation per chart.
What causes Condensate Fault Code 6 on my ClimateMaster Heat Pump?
If your ClimateMaster Heat Pump displays Condensate Fault Code 6, it could be due to several reasons: * Blocked drain: Check for blockage and clean the drain. * Improper trap: Check trap dimensions and location ahead of vent. * Poor drainage: Check for piping slope away from the unit and the slope of the unit toward the outlet. Also, check the vent location. * Moisture on sensor: Check for moisture shorting to the air coil. * Plugged air filter: Replace the air filter. * Restricted Return Air Flow: Find and eliminate the restriction. Increase return duct and/or grille size.
What does Over/Under Voltage Code 7 mean on my ClimateMaster Heat Pump?
If your ClimateMaster Heat Pump displays the Over/Under Voltage Code 7, which auto-resets, it indicates a voltage issue. For Under Voltage, check the power supply and 24VAC voltage before and during operation, the power supply wire size, and compressor starting (consider a hard start kit). Also, check the 24VAC and unit transformer tap for correct power supply voltage. For Over Voltage, check the power supply voltage and 24VAC before and during operation, and the 24VAC and unit transformer tap for correct power supply voltage.
What does Unit Performance Sentinel Code 8 mean on ClimateMaster Tranquility TTH072 Heat Pump?
If your ClimateMaster Heat Pump displays Unit Performance Sentinel Code 8, it indicates a performance issue. If in heating mode and LT2 is greater than 125°F [52°C], check for poor air flow or an overcharged unit. If in cooling mode and LT1 is greater than 125°F [52°C] or LT2 is less than 40ºF [4ºC], check for poor water flow or air flow.
General| Type | Water Source Heat Pump |
|---|---|
| Refrigerant | R-410A |
| Compressor Type | Scroll |
| Voltage | 208-230V |
| Phase | 3 |
| Model | TTH072 |
Provides warnings, cautions, and notices for installation, service, and troubleshooting.
Instructions for suspending horizontal units using hanger kits and vibration isolators.
Emphasizes proper duct sizing, design, and connections for unit performance and noise reduction.
Provides step-by-step instructions for converting the air discharge from side to back.
Details requirements for condensate drain lines, pitching, traps, and venting for horizontal units.
Explains condensate piping for vertical units, noting internal trap and no external trap needed.
Guidelines for installing supply and return piping, including valves, strainers, and hose length.
Describes commercial systems connected to common piping, insulation, and hose kits.
Details typical closed loop ground source system, materials, and pressure testing.
Describes open loop piping, shut off valves, P/T plugs, and material compatibility for ground water systems.
Instructions for matching available power to unit specifications and following codes.
Details line voltage connection to the contactor side and consulting electrical data for fuse size.
Details thermostat wiring to the ECM control board or terminal block, referring to diagrams.
Guidelines for thermostat placement, wall mounting, and wiring, emphasizing 18 AWG wire.
Typical wiring diagram for units with CXM board and ECM fan motor (single phase).
Typical wiring diagram for units with ClimaDry® (single phase).
Typical wiring diagram for units with CXM, ECM, and MPC (DDC) controls (single phase).
Details CXM control features including test mode, configuration options, and DIP switches.
Details DXM control features including test mode, configuration options, DIP switches, and accessories.
Details the three operating modes (cooling, cooling with reheat, heating) and thermostat compatibility.
Provides step-by-step instructions for cleaning and flushing the WLHP piping system.
